User manual CASIO AL-150R

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] 6 : Phrase end point is adjusted to eighth note-unit positions. bn REC will light when recording starts. 3. When recording reaches the point where you want to stop, press bn bn PLAY/STOP. bn Note Quantize (Note Qntz) When recording keyboard play, there may be cases when your timing strays a bit. The note quantize settings described below can be used to correct the timing of keyboard play automatically and correct the timing of notes you play on the keyboard. (Note that only key press timing is correct. The timing of other operations such as key release, and wheel, pedal, and knob operations are not corrected. ) Off : Timing not adjusted. (Notes are recorded as played. ) 6, , 7, : Timing of actual keyboard play is corrected to the nearest note in accordance with the specified note unit. · Pressing MENU will display a menu of the detailed settings shown below. Use the up (q) and down (w) buttons to select a parameter and then use the minus (­) and plus (+) buttons to change its setting. REC will become unlit and "!TEMP" (temporary) will appear for the phrase number. · Pressing REC in place of PLAY/STOP in step 3 above will stop recording, temporarily change to the overdub standby mode, and start looped playback of the phrase you have recorded. For details about overdubbing, see "Recording Over Another Phrase (Overdubbing)" (page E-47). bn 4. After you finish recording, save the data as described below. · Press WRITE to display the screen for saving a phrase (page E-48). ­127 to 000 to +127 bn PLAY/STOP. Key Shift E-47 Recording and Playing Back Phrases To pause overdubbing during looped playback In step 4 of the above procedure, press REC instead of PLAY/STOP. · This will cause REC to start flashing. · Though what has been recorded up to that point continues to play as a loop, further recording is not possible while overdubbing is paused. · Press REC again to resume overdubbing. bn bn bn To save a phrase Press 7 WRITE to display the screen for saving a phrase. Save the phrase by performing the same operation as that for saving a user tone (page E-12). bn To delete the last recorded data (undo) While phrase playback is in progress or stopped, or while overdubbing is in progress or paused, hold down REC until the undo screen appears. bn · The message "Can't UNDO" will be appear on the display if you try to perform an undo operation again after already undoing the last recording. · If there is not enough Synthesizer memory space available to store the phrase data, the message "not enough space" will appear on the above display in place of "Press Enter", and you will not be able to save the phrase data. If this happens, delete some of the user data in Synthesizer memory to free up memory space. · The Synthesizer can store up to 100 user phrases with a combined total of up to 128KB. · For information about deleting phrase data you saved, see page E-71. Saving a Phrase to an External Device · Memory card (page E-73) · Computer (page E-79) · A phrase that has been saved as a user phrase cannot be undone. Indicators Next to Phrase Numbers The meanings of the indicators that are appended to the phrase number on the display are described below. : Unsaved phrase * : Saved user phrase !TEMP : Newly recorded phrase that has not been saved · If you change the phrase number selection in step 2 of the procedure under "To play back a preset" while an exclamation point (!) is appended to the currently selected phrase number (indicating that it is an unsaved user phrase), the unsaved user phrase will be discarded. To save an unsaved user phrase, use the procedure under "To save a phrase", below. E-48 Using the Step Sequencer 7 bm bo bp 4 5 9 bk bl bq 1 2 The Step Sequencer provides up to 16 steps. The Synthesizer's sliders can be used to control step notes and velocity in real time. [. . . ] Parameters and Value Ranges: 1 :Wow and Flutter Rate (0 to 127) Adjusts the wow and flutter rate. 2 :Wow and Flutter Depth (0 to 127) Adjusts the wow and flutter depth. 3 :Noise1 Level (0, 1, 2, 3, 4, 5) (Param A) Adjusts the level of Noise Generator 1. 4 :Noise2 Level (0, 1, 2, 3, 4, 5) (Param B) Adjusts the level of Noise Generator 2. [. . . ]