User manual CASIO AP-25

[. . . ] This product should be used only with a stand that is specified by the manufacturer. This product, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. [. . . ] · Pedal effect data recorded to the memory is applied to playback from the memory, and does not affect your performance on the keyboard. Likewise, pedal operations on the CELVIANO are applied to the keyboard only, and not to playback from the memory. C4 C 7 (black key) B 5 (black key) · A note does not sound when you press a keyboard key while holding down CONTROL. NOTE The Keyboard Channel is automatically set to 1 whenever you turn on CELVIANO power. Assigning Tones to Individual Channels You can assign tones to channels using a Program Change message sent from a connected MIDI device. You cannot change the tone assigned to each channel from the CELVIANO. NOTE The tone GRAND PIANO is automatically assigned to all channels whenever you turn on CELVIANO power. E-22 427B-E-026A AP31/33_E_21_25. p65 Page 22 03. 10. 7, 11:00 AM Adobe PageMaker 6. 5J/PPC Program Change Number Settings The tones of your CELVIANO have two different sets of program numbers: Type 1 sequential numbers and Type 2 numbers that correspond to the General MIDI System (see "General MIDI" on page E-24). The tables below show the program numbers that are assigned, depending on whether you select Type 1 or Type 2 using the procedure under "To change the program change number type" on page E-24. Type 1 Tone Name MSB GRAND PIANO MELLOW PIANO GRAND PIANO 2 ELEC PIANO 1 ELEC PIANO 2 HARPSICHORD PIPE ORGAN STRINGS 0 0 0 0 0 0 0 0 Send Bank Select LSB 0 0 0 0 0 0 0 0 Program numbers 0 1 2 3 4 5 6 7 Receive Bank Select MSB 0 0 0 0 0 0 0 0 LSB 0 0 0 0 0 0 0 0 Program numbers 0 1 2 3 4 5 6 7 Type 2 Tone Name MSB GRAND PIANO MELLOW PIANO GRAND PIANO 2 ELEC PIANO 1 ELEC PIANO 2 HARPSICHORD PIPE ORGAN STRINGS 2 3 0 16 0 0 24 0 Send Bank Select LSB 0 0 0 0 0 0 0 0 Program numbers 0 0 0 4 4 6 19 48 Receive Bank Select MSB 2 3 0 16 0 0 24 0 LSB 0 0 0 0 0 0 0 0 Program numbers 0 0 0 4 4 6 19 48 Corresponding General MIDI Sound -- -- Acoustic Grand Piano -- Electric Piano 1 Harpsichord -- Strings Ensemble 1 427B-E-027B E-23 AP31/33_E_21_25. p65 Page 23 03. 10. 7, 11:00 AM Adobe PageMaker 6. 5J/PPC To change the program change number type While still holding down the CONTROL button, select the Program Change Mode by pressing one of the keyboard keys illustrated below. A 5 (black key): TYPE 1 Turning Local Control On and Off This setting effectively determines whether or not the keyboard and pedals of the CELVIANO are connected to the CELVIANO's sound source, as illustrated below. MIDI OUT IN C4 A5: TYPE 2 Keyboard Sound source ON Pedals OFF Local Control · A note does not sound when you press a keyboard key while holding down CONTROL. · See the table on page E-23 for detailed information about Type 1 and Type 2. General MIDI The General MIDI System is a set of specifications for sound generating devices agreed upon by world MIDI manufacturers. These specifications were developed to allow the creation of music data that is not limited to specific equipment makers and models. Among other things, General MIDI defines the tone number sequence and the number of MIDI channels that can be used. Any device equipped with a sound source that supports General MIDI is able to produce sounds of similar nuances, regardless of the manufacturer or model. The Type 2 program change numbers of your CELVIANO assign program numbers to tones so they comply with the General MIDI System. Type 2 program change numbers make it possible to receive General MIDI System data from a connected sequencer or other device, and play it using the CELVIANO's tones. Turn off CELVIANO power and then check to make sure that the pedal plug is securely connected to the piano's pedal connector. Move VOLUME knob more towards the MAX side. Disconnect the headphones from the piano. Contact your CASIO Service Provider for replacement of the lithium battery. Change the Keyboard Channel settings so they are identical. Change the volume or expression setting of the external sound source to an appropriate value. Reference Page E-12 Page E-10 Page E-24 Page E-19 Keyboard out of tune. 1. Transpose is set to a value other than 0. Incorrect tuning setting Page E-20 Pedal effect continues to be applied even though pedals are not pressed. Problem with the connection between the pedals and piano. Page E-29 No sound produced by demo tune play. 1. Headphones connected to the piano. Page E-12 Page E-10 Memory contents deleted. Lithium battery is dead. Page E-7 No sound produced by connected external MIDI sound source when CELVIANO keys are pressed. 1. CELVIANO Keyboard Channel does not match the Keyboard Channel of the MIDI sound source. Volume or expression setting of the external sound source is set to 0. Page E-22 See the documentation that comes with the external sound source. E-26 427B-E-030A AP31/33_E_26_30. p65 Page 26 03. 10. 7, 11:00 AM Adobe PageMaker 6. 5J/PPC Assembly Instructions · Illustrations in this User's Guide shows the AP-25. 1 Assembling the stand Refer to Figures 3, 4 and 5 as you assemble the stand according to the following procedure. Caution · Take particular care to avoid injury when installing legs and pedals, and when mounting the keyboard onto the stand. [. . . ] Reconocimiento La recepción de este mensaje silencia inmediatamente todos los sonidos que se ejecutan sobre los canales MIDI. Controlador de reposición completa # Formato 1er. byte 00H RPN nulo RPN MSB = 7FH RPN LSB = 7FH Reconocimiento Una vez que se envía un RPN nulo, todos los MSB y LSB de ingreso de datos recibidos son ignorados, hasta que se reciba otro mensaje RPN diferente a RPN nulo o un mensaje NRPN. n . . . . . . . Número de canal de voz = 0H a FH (canal 1 al canal 16). Reconocimiento La recepción del mensaje del controlador de reposición completa ocasiona que los controladores siguientes se reposicionen. [. . . ]