User manual CASIO CT700

[. . . ] E-6 Other Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-7 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-9 Using the User Documentation on the CD-ROM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-9 Projector Features and Main Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10 General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10 Remote Controller General Guide . . . . . . . . . . . E-12 Preparing the Remote Controller. . . . . . . . . . . . . [. . . ] When connecting a video camera or other video device with a special video output terminal, use the special cable that comes with the video device. For details, see the documentation that comes with the video device. E-17 English Getting Ready Connecting to a Component Video Output Device Some video devices are equipped with a component video output terminal. You can use an optionally available component video cable (YK-3) to connect the COMPUTER terminal of the projector to the component video output terminal of a video device. Always turn off the projector and the video device before connecting them. Projector AV terminal COMPUTER terminal To component video output terminal Video device Optional component video cable (YK-3) Bundled special AV cable White Red To AUDIO output terminal Yellow (Not connected) You can use the optional YK-3 component video cable to connect to pin jack (RCA) type component video output terminals. The projector does not support connection to any other type of terminal. Component video output terminals come in 3-terminal sets: Y·Cb·Cr or Y·Pb·Pr. Be sure to match the colors of the plugs on the optional YK-3 component video cable with the colors of the terminals (Green: Y; Blue: Cb/Pb; Red: Cr/Pr). Note that connection only to an analog component video output terminal is supported. Connection to a digital output terminal is not supported. E-18 Getting Ready Connecting a USB Device to the Projector (USB Port Equipped Models Only) English If you have an XJ-SC215/XJ-S37/XJ-S47/XJ-S57 model projector, you can connect any of the following USB devices to the projector's USB port. USB Memory Device* You can transfer image and movie data from your computer to a USB memory device and take it along with you for projection with the projector. The projector comes with software that converts Microsoft PowerPoint sheets to images, which you can then store to a USB memory device. This means you can include PowerPoint data in your presentations without having to lug a computer along everywhere you go. The cool down state is indicated by the POWER/STANDBY indicator flashing orange. Note that the projector will not turn on until cool down is complete, even if you press the [ ] (power) key. The projector will turn on and enter the standby state after cool down is complete. The password feature lets you limit use of the projector to specific individuals. For more information, see "Option Settings 1 Power On Password" in the User's Guide (UsersGuide_English. pdf) on the CD-ROM that comes with the projector. Specifying the Display Message Language A "Language" window will be projected the first time you turn on the projector. Use the menu on this screen to specify the display language you want to use. 1. Use the cursor [ ] and [ ] keys to highlight the language you want to use. 2. Press the [ENTER] key. Direct Power On You can configure the projector so it powers up automatically as soon as you plug it into a power source. With this "Direct Power On" feature, you do not even need to press the [ ] (power) key. To enable Direct Power On, display the Setup Menu, and then change the "Direct Power On" setting to "On". When you have Direct Power On enabled, do not leave the projector plugged into an electrical outlet while it is turned off. If you do, there is the chance that it (and the lamp) might turn on automatically when power is restored after being cut off by a power outage, tripping of a breaker, etc. Direct Power On causes the projector to turn on automatically as soon as it is plugged into a power outlet. This greatly reduces the amount of time it takes until you are ready to start projecting. Note, however, that the actual startup sequence (Standby State Power On Warm Up Projection Starts) that the projector performs is the same, regardless of whether Direct Power On is enabled or disabled. [. . . ] Try using the projector's AV terminal (see "Connecting to a Standard Video Device"). The wrong option ("Component" or "RGB") may be selected for the "Input Settings COMPUTER Terminal" setting on the setup menu. The image will not be projected correctly if "Component" is selected while the projector's COMPUTER terminal is connected to the RGB output terminal of a computer, or if "RGB" is selected while the projector's COMPUTER terminal is connected to the component video output terminal of a video device. Use the setup menu to change the "Input Settings COMPUTER Terminal" setting to "Auto" to correct the problem. [. . . ]