User manual CASIO CTK-625L

[. . . ] 8 Sound Source Instrument Part Sub-block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 MIDI Send by Auto-accompaniment, Song Memory, and the SMF Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1 Product Configuration as a MIDI Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 Conditions that Disable Message Send and Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Also note that receipt of this message may also change the Part Mode parameter at the same time. For more information, see "12. 1 About the Part Mode" below. 12. 1 About the Part Mode Each of this Model's parts has a parameter called "Part Mode, " which can be set to Normal Mode, Drum Mode, or Drawbar Organ Mode. Melody tones are set to Melody Mode, rhythm tones that use the drum map are set to the Drum Mode, and drawbar organ tones are set the to Drawbar Organ Mode. 13 Format Channel Aftertouch n: MIDI Channel Number vv: Value Message Format: DnH vvH Send These messages are never sent. Receive Receipt of this message adds vibrato to the voice that is sounding. Details of the effect differ according to the tone setting. 14 Format Pitch Bend n: MIDI Channel Number ll: Value LSB mm: Value MSB Message Format: EnH llH mmH Send Sent when the bender wheel is operated (WK-3200/WK-3700 only). Also sent when play data or auto-accompaniment data that includes bender wheel data is played back. Receive Receipt changes the pitch of the currently sounding note. The width of the change depends on the setting of the Transpose/Function's Bend Range parameter and the Pitch Bend Sensitivity, whose setting is configured by RPN. 24 Part III System Message 15 Format Message Format: FEH Send This message is never sent. Receive When this message is received once, the Active Sensing mode is entered. If no MIDI Message is received for a particular amount of time, voices being sounded by this Model's sound source are released, controller is reset, and Active Sensing mode is exited. Active Sensing 16 Format System Exclusive Message Message Format: F0H. . . . F7H This Model can send and receive Universal System Exclusive Messages, as well as System Exclusive Messages that have a format that is unique to this Model. 16. 1 Format Universal Realtime System Exclusive Message 7FH. . . . F7H Message Format: F0H 16. 1. 1 Format Master Volume Message Format: F0H 7FH 7FH 04H 01H llH mmH F7H ll: Value LSB (Note 1) mm: Value MSB (Note 1) Note 1: The setting value matches the value that is sent and received. Receive Receipt changes the Master Volume parameter. Receive Though this Model does not support GM2, receipt of the GM2 System On message has the same result as receipt of the GM System On message. 29 16. 1. 8 GS Message Message Format: F0H 41H 10H 42H 12H 40H 00H 7FH 00H 41H F7H Send This message is never sent. Receive Receipt performs the same operation as when the GM System On message is received. 16. 2 Format CTK-625L/WK-3200/WK-3700 System Exclusive Message Message Format: F0H 44H 11H 02H. . . . F7H These messages can control most of the this Model's parameters, as well as user data send/receive with Flash memory and come commands. For more information, see "Part IV This Model's System Exclusive Messages". 30 Part IV This Model's System Exclusive Messages 17 17. 1 Format Message Classifications This Model's SysEx operations are classified as Parameter type for send and receive of an individual Parameter, and Parameter Set type for Bulk send and receive of a set of parameters. These SysEx types can be further broken down into parameter categories according to the item being transferred. CTK-625L/WK-3200/WK-3700 System Exclusive Messages Individual Parameter Transfer Command Patch Status and Commands Common MIDI Tune/Mix Sys Chorus Sys Reverb Master EQ DSP Basic Tune/Mix Tone Drawbar Vibrato Part Wave Data Information Song Data Information Rhythm Data Information SMF Data Information Parameter Set Bulk Transfer User Tone User Timbre User Drum User Instrument User Wave Parameter User Wave Data User DSP Song User Rhythm Pattern Registration User Drawbar SMF The operation classification of a message is determined in accordance with the value of the "Action" field of this Model's SysEx message. The basic format for all operation type messages is described in "17. 2 Message Structure", below. 31 17. 2 Message Structures This Model's System Exclusive Messages is formed of the 13 fields shown below. Whether or not a particular field is included in a message and the length of each field depends on the message. The minimum unit for the length of each field is bytes. If two values are contained within the same byte, they are separated by a slash (/). 1 SYSEX 2 MAN 3 MOD 4 dev 5 act 6 cat 7 prm 8 ilen/dlen 9 ps 10 index 11 data 12 sum 13 EOX The "act" field describes the action that the message performs. The meanings of the "index" and "data" fields differ according to the content of the act field. [. . . ] F7 System Exclusive Format 01 02 03 04 05 06 07 08 09 10 11 12 13 SYSEX MAN MOD dev act cat prm ps index data sum EOX ilen/dlen See "IV This Model's System Exclusive Messages". Data Format Bulk dumping SMF data transfers the data with a 128-byte header appended as shown below. The header data starts with an 8-byte file name, which is displayed by this Model after receipt. Header 128Bytes Name 8Bytes Reserved 120Bytes SMF Data 64 38 Flash Memory Image Parameter Set This Parameter Set is used for dumping flash memory contents. One Parameter Set corresponds to an image block of 2 Mbytes of flash memory. [. . . ]