User manual CASIO DQ-950

[. . . ] HUMIDITY MAX/MIN MAX/MIN ALARM SNOOZE ON OFF CLEA 5 3 R °C / °F 8 SET + ­ RESET RESET · A sticker is affixed to the glass of the clock when you purchase it. Be sure to remove the sticker before using the clock. · Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the illustration. Alarm Off PM indicator Current time (Hour, minutes, seconds) Snooze Alarm On Alarm on indicator DATE (month - date) Day of the week Current Temperature RESET Current Humidity Alarm time Snooze on indicator 1 Operation Guide DQ-950 GENERAL GUIDE 1 SNOOZE/LIGHT button · Press this button to illuminate the display for about four seconds. [. . . ] · Each press of + (UP) or ­ (DOWN) while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour and 24-hour timekeeping. After making the settings you want, use the SET button (5) to display the Normal Timekeeping Screen. · The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for about three minutes without performing any operation. USING THE ALARM The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm Mode selector (2) to select the snooze alarm feature. Use the ­ (DOWN) and + (UP) buttons (3) to set the alarm time. Pressing the ­ (DOWN) and + (UP) buttons (3) causes the alarm time to appear in place of the date on the display. SET Setting the Alarm Time USING THE CLOCK 1. Press the SET button (5) to cycle through the setting screens as shown below. Normal Timekeeping Screen + ­ Press to change the alarm time setting (--) Press to change the alarm time setting (+) · Holding down + (UP) or ­ (DOWN) changes the digits at high speed. Year Setting Screen 12-hour/24-hour Timekeeping Screen Turning the Alarm On and Off Use the Alarm Mode selector (2) on the side of the clock to turn the alarm on and off, and to select the snooze feature. Alarm Mode selector SNOOZE Description The alarm sounds at the preset time for one minute, and seven more times every five minutes thereafter. Even if you stop the alarm by pressing the SNOOZE/LIGHT button (1), the alarm sounds again five minutes later. flashes on the display to indicate that the snooze feature is · The indicator activated. The alarm sounds at the preset time for one minute. The alarm does not sound. ON Month and Day Setting Screen Time Setting Screen OFF · The alarm time appears in place of the date on the display whenever the Alarm Mode selector (2) is set to ON or SNOOZE. · The light also turns on for the first four seconds that the alarm sounds. · The volume of the alarm sound cycles through five levels as it sounds. Stopping the Alarm · When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on, the alarm will sound again in about five minutes. · To turn off the snooze feature, slide the Alarm Mode selector (2) to OFF. 2 Operation Guide DQ-950 USING THE LIGHT Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark. HYGROMETER FUNCTIONS A built-in sensor measures humidity and shows the measured value on the display. Important! · Overuse of the light can shorten battery life. Humidity Measurements · The humidity display shows "LO" for humidity below 10% and "HI" for humidity above 90%. THERMOMETER FUNCTIONS A built-in sensor measures temperature and shows the measured value on the display. The readout from the temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F). High Humidity and Low Humidity Memory · The clock remembers the high and low humidity values it measured since the last time its humidity memories were cleared. You can recall these values as shown below. Current temperature and humidity High humidity and low humidity Temperature Measurements · The temperature display shows "LO" for temperatures below ­50°C (­58°F) and "HI" for temperatures above 70°C (158°F). · Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such readings are actually outside the guaranteed temperature range of this clock. MAX/MIN HUMIDITY button (9) Switching between Celsius and Fahrenheit Celsius (°C) · Push the °C/°F button (4) to select either Celsius (°C) or Fahrenheit (°F). Fahrenheit (°F) · To clear the high humidity and low humidity memory, press the MAX/MIN HUMIDITY button (9) to display the current high/low values, and then press the CLEAR button (6). Note that the current high/low values are displayed for only about five seconds, and you need to press the CLEAR button (6) during that period. °C/°F button (4) °C °F CLEAR button (6) High Temperature and Low Temperature Memory · The clock remembers the high and low temperatures it measured since the last time its temperature memories were cleared. [. . . ] · Be sure to load the batteries with their positive (+) and negative (­) ends facing correctly. · Never mix old and new batteries, or batteries of different brands. · Never charge the batteries that come with the clock. · Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto your skin. [. . . ]