User manual CASIO DQR-100

[. . . ] button Press this button to display the high and low temperature values. 8 CLEAR button Press this button to clear the currently displayed high/low temperature. 9 °C/ °F button Press this button to toggle the temperature units between Celsius and Fahrenheit. 0 RE-SYNC button Press this button to re-synchronize the timing of the main unit and the sub-unit. [. . . ] If this happens, try changing the position or orientation of the clock, and press the WAVE button (4) to receive again. · Press the WAVE button (4) to start a calibration signal receive operation. · Use the WAVE button (4) to perform a receive operation after replacing the clock's batteries or if the auto receive operation was not performed correctly for some reason. · The clock beeps and display illumination flashes for about three seconds when a receive operation trigged by the WAVE button (4) is successful. Manual Receive Important! · Do not perform any button or switch operation while a signal receive operation is in progress. · The time calibration signal includes both Standard Time and Daylight Saving Time (summer time) data. · The DST indicator appears on the display when Daylight Saving Time (summer time) data is received. 2 Operation Guide DQR-100 Setting the Time and Date Manually · When using the clock in an area that is outside of the range of the transmitter in Mainflingen or in an area where signal reception is impossible for some reason, you need to manually adjust the time as required. Press the SET button (3) to cycle through the setting screens as shown below. Normal Timekeeping Screen USING THE ALARM The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm Mode selector (5) to select the snooze alarm feature. Setting the Alarm Time Use the Alarm Time Set buttons (2) to set the alarm time. Pressing the Alarm Time Set buttons (2) causes the alarm time to appear in place of the date on the display. °F Press to change the alarm time setting (+). RESET O W N (­ ) U ) P(+ SET Year Setting Screen 12-hour/24-hour Timekeeping Screen · Holding down + or ­ changes the digits at high speed. Turning the Alarm On and Off Use the Alarm Mode selector (5) on the side of the clock to turn the alarm on and off, and to select the snooze feature. Alarm Mode selector SNZ Description The alarm sounds at the preset time for one minute, and seven more times every five minutes thereafter. Even if you stop the alarm sound by pressing the SNOOZE/LIGHT button (1), the alarm operation is performed again five minutes later. · The indicator flashes on the display to indicate that the snooze feature is activated. The alarm sounds at the preset time for one minute. Month and Day Setting Screen Time Setting Screen ( ( ) ) ALM ON 2. While the screen you want is on the display, use the Alarm Time Set buttons (2) to change the digits that are flashing. ALM OFF The alarm does not sound. RESET RE Press + to increase the flashing digits. TEMP. MAX/MIN -SYN C °C / CLEAR Press -- to decrease the flashing digits. · The alarm time appears in place of the date on the display whenever the Alarm Mode selector (5) is set to ON or SNZ. · The light also turns on for the first four seconds that the alarm sounds. · The alarm sound changes over four levels as it sounds. °F SET Stopping the Alarm D O W N (­ ) · Holding down + or ­ changes the flashing digits at high speed. · You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with the date setting. · Pressing + or ­ while the Time Setting Screen is on the display causes the seconds count to be reset to 00. · Each press of + or ­ while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour and 24-hour timekeeping. [. . . ] · Never charge the batteries that come with the clock. · Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto your skin. · Replace the batteries at least once a year, even if the current batteries are working properly. · The batteries that come with the clock lose some of their power during transport and storage. Sub-unit high temperature and low temperature THERMOMETER FUNCTIONS Both the main unit and the sub-unit are equipped with their own temperature sensors. [. . . ]