User manual CASIO DR-210HD

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] Registration memory has eight banks, each of which is divided into eight areas. Registration Data The following are the settings that are stored as registration data when you save a Digital Piano setup. · Layer ON/OFF · Split ON/OFF · Split point · Reverb ON/OFF · Reverb type · Chorus ON/OFF · Chorus type · Each zone tone number · Each zone INT/EXT ON/OFF · All common parameters (page E-18) · All zone parameters (page E-28) · Following function menu items (page E-38) · Touch Response · Pedal Assign · Temperament type · Temperament key note · Stretch Tuning · Acoustic Resonance ON/OFF · Half Pedal Effect NOTE To save a setup as registration data 1. 2. Configure the Digital Piano with the settings you want to save. Press the br (REGISTRATION) button so the lamp below it is lit. This is the REGISTRATION mode. Lit Bank number · The Digital Piano's current mode (MASTER CONTROL, CARD PLAYER, ZONE EDIT) is not included in registration data. This means that the Digital Piano's mode does not change when you recall registration data. · The following function menu settings are not included in registration data. You can, however, perform the backup operation (page E-40) to retain these settings when the Digital Piano is turned off. · Tuning · EQ Hold · Display Contrast · Song MIDI Out · Song Volume · Song Pre-count · Song Repeat · The backup operation (page E-40) saves all of the above function menu settings, as well as all of the settings that are included in registration data. 3. Use the bt (w, q) buttons to scroll through the banks (1 to 8) until the bank where you want to save the registration data is displayed. E-34 Using Registration Memory 4. ck cl cm cn co cp cq cr dm 2. Use the bt (w, q) buttons to scroll through the banks (1 to 8) until the one you want to rename is displayed. · This displays a screen for editing the name. · Pressing a number button immediately executes the registration data save operation. · The following shows how the display would appear if you select Bank 1, Area 3. Area number Bank number 3. Edit the name. · The initial default name of all the banks is "REGIBANKNAME". · Use the ct (u) and dk (i) buttons to move the cursor left and right, and the bt (w, q) buttons to scroll through characters at the current cursor position. 3. Press the br (REGISTRATION) button so the lamp below it is lit. If you are recalling a file that contains data for a single bank, use the bt (w, q) buttons to scroll through the bank numbers (1 through 8) until the one to which you want to recall the data is displayed. · If you are recalling a file that contains data for all banks, you can skip this step. 4. 5. While holding down the bs (FUNCTION) button, press the bl (LOAD/SAVE) button. · This enters the LOAD/SAVE mode. Depending on the type of operation you want to perform, use the ct (u) and dk (i) buttons to display one of the screens shown below. To recall a file that contains data for a single bank To recall a file that contains data for all banks 6. Use the bt (w, q) buttons to display the file that contains the data you want to recall, and then press the dl (ENTER) button. · This will cause the message "Replace?" to appear. · To cancel the recall operation and exit the LOAD/ SAVE mode, press the cs (EXIT) button. E-37 English 1. Depending on where the file is located, perform one of the steps shown below. To replace the registration data currently in the bank(s) you selected with the registration data in the file, press the bt (YES) button. To return to the screen in step 6 of this procedure without recalling anything, press the bt (NO) button. · Pressing the bt (YES) button recalls the data from the Using the Function Menu MASTER CONTROL CARD PLAYER The function menu contains global settings (overall tuning and touch adjustment, local control ON/OFF, etc. ) that need to be changed by you relatively infrequently. It also includes some SD card operations (format, etc. ) 3. Use the bt (w, q) buttons to change the currently displayed setting. · Holding down the bs (FUNCTION) button as you press w or q will change the setting by a factor of 10. Function Menu Operations This section explains operations involving function menu settings. For details about specific function menu items, see "Function Menu Settings" (page E-39). 4. To exit the function menu, press the cs (EXIT) button or the bs (FUNCTION) button. IMPORTANT! To change the setting of a function menu item 1. Press the bs (FUNCTION) button. · The button's lamp will light, and the display will change as shown below. · Turning off the Digital Piano causes all function menu settings to return to their initial defaults. If you need to save a function menu setup, perform the backup operation. For details, see "Backup" (page E-40). [. . . ] Adjust this parameter to eliminate such distortion. 1 : Resonance (0 to 127) Adjusts the strength of resonance. 2 : Manual (0 to 127) Adjusts the wah filter reference frequency. 3 : Depth (­64 to 0 to +63) Adjusts the depth of the wah in accordance with the level of the input signal. [. . . ]