User manual CASIO EXILIM EX-H20G

[. . . ] E Digital Camera User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ To go to "Getting the Most Out of Dynamic Photo" click here! 1 Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] Use [8] and [2] to select "Save" and then press [SET]. The message "Saving data. Please wait. . . " will appear, indicating that the positioning log data is being written to the memory card. NOTE · A new KML file is created in memory each day. The dates used for the date and time entries within a KML file are based on the current time setting of the camera when the "Output Log" operation is performed. · KML files are stored in a KML folder, which is located inside the memory card's DCIM folder. · The Output Log function cannot be used if there is no memory card loaded in the camera, if the memory card loaded in the camera is full, or if the camera's battery cover is open. · You can import the KML files to Google Earth or some other map software and track your movements on your computer screen. Enabling Movement of the Image Cursor (Move Cursor) Procedure [ý] (MAP) * [MENU] * MAP Tab * Move Cursor See page 104 for details. Adjusting the Accuracy of the Direction Sensor (Direction Adj) The camera's built-in direction sensor may not operate normally if there is a source of magnetism nearby. If you feel that direction measurements are not correct, perform the following procedure. 1. 2. Turn on the camera and then press [ý] (MAP). On the "MAP" tab, select "Direction Adj". B 106 Using the Hybrid-GPS 3. Taking care not to drop the camera, slowly swing it around in a figure eight for about 10 seconds. Use the wrist of the hand that is holding the camera to move in a way that forms a figure eight. This will correct for the magnetism and adjust direction sensor accuracy. The message "Completed normally. " will appear to let you know that accuracy adjustment is complete, and the map screen will return to the display. · If the message "Correction failed. Try again. " appears, perform the above procedure again. · Performing this adjustment near a train, an automobile, a magnet, or a concentration of metal can result in incorrect adjustment. · Direction sensor adjustment is not supported while "Off" is selected for the "GPS" setting (page 92). Converting Location Information of Images from Another Source for Playback on This Camera (Update Info) You can use this procedure to convert position information (latitude and longitude) accompanying an image recorded on another manufacturer's camera so it can be played back in the MAP mode of this camera. 1. 5. Use the Photo Transport that comes with the camera to copy the other manufacturer's image with position information from your computer to a memory card (page 129). Turn off the camera and load the memory card that contains the data. Turn on the camera and then press [ý] (MAP). On the "MAP" tab, select "Update Info" and then press [6]. Use [8] and [2] to select "Update" and then press [SET]. The message "Busy. . . Please wait. . . " will appear as the data is being transferred. After that, the image with position data will be displayable in the MAP mode. IMPORTANT! · The position information of certain types of images may not be able to be updated. B 107 Using the Hybrid-GPS Other Settings (Set Up Tab Menu) For information about menu operations, see page 58. [. . . ] Use [4] and [6] to select the background image you want and then press [SET]. Select the image you want to use as the background. Here, select the image you recorded in step 1 of this procedure. * Only images that are able to be used as background images will appear for selection at this time. · Only an image that satisfies the following conditions can be used as a background image. ­ A snapshot or movie recorded with this camera or a snapshot transferred to this camera's memory using Photo Transport ­ A snapshot with an aspect ratio of 4:3 3 Creating a Dynamic Photo Image 4. Use [4] and [6] to select the built-in subject that you want to insert into the image and then press [SET]. * Only built-in subjects that can be inserted into other images will appear at this time. 5. [. . . ]