User manual CASIO EXILIM EX-ZR10

[. . . ] E Digital Camera User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ To go to "Getting the Most Out of Dynamic Photo" click here! Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] Failure to insert the connector fully can result in poor communication or malfunction. · Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration. · Make sure that the camera is turned off before plugging in or unplugging the cable. Check the user documentation that comes with the TV for information about requirements before plugging into or unplugging from the TV. 2. Turn on the TV and select its video input mode. If the TV has more than one video input, select the one where the camera is connected. 105 Viewing Snapshots and Movies 3. Press [p] (PLAY) to turn on the camera. This will cause an image to appear on the TV screen, without anything appearing on the camera's monitor screen. · Pressing [ON/OFF] (Power) or [r] (REC) will not turn on the camera while the AV cable is connected. · You also can change the aspect ratio of the screen and the video output system (page 158). 4. Now you can display images and play back movies as you normally do. IMPORTANT! · Before connecting to a TV to display images, be sure to configure the camera's [r] (REC) and [p] (PLAY) buttons for "Power On" or "Power On/Off" (page 157). · Audio is initially output by the camera at maximum volume. When you first start displaying images, set the TV volume control at a relatively low level and then adjust it as required. NOTE · Audio is stereo. · Some TVs may not be able to output images and/or audio correctly. · All icons and indicators that appear on the monitor screen also appear on the TV screen. You can use [8] (DISP) to change the display contents. 106 Viewing Snapshots and Movies Viewing High-quality Movies on a Hi-Vision Television Use a commercially available HDMI cable to connect the camera to the TV. For information about playback, see the procedure starting from step 2 under "Viewing Snapshots and Movies on a TV Screen" on page 105. · Use a commercially available HDMI cable that is marked with the logo shown to the right. HDMI connector HDMI cable (commercially available) HDMI output (Mini) HDMI input HDMI mini connector Terminal cover IMPORTANT! · Output to a TV is not supported while the camera is in the REC mode. NOTE · Use a HDMI cable that with a plug that is compatible with the camera's HDMI mini connector on one end, and a plug that is compatible with your TV's HDMI connector on the other end. · Proper image and/or audio output and other operations may not be possible with some devices. · Connecting the camera to the HDMI connector of another device can damage both the camera and the other device. Never connect two HDMI output connectors to each other. · Make sure that the camera is turned off before plugging in or unplugging the cable. Check the user documentation that comes with the TV for information about requirements before plugging into or unplugging from the TV. · When cables are connected to both the USB/AV port and the HDMI output connector, the HDMI output connector connection is given priority. · Disconnect the HDMI cable when you are not using HDMI output. The camera's monitor screen may not operate normally while the HDMI cable is connected. · Some TVs may not be able to output images and/or audio correctly. [. . . ] Use [4] and [6] to select the background image you want and then press [SET]. Select the image you want to use as the background. Here, select the image you recorded in step 1 of this procedure. * Only images that are able to be used as background images will appear for selection at this time. · Only an image that satisfies the following conditions can be used as a background image. ­ A snapshot or movie recorded with this camera or a snapshot transferred to this camera's memory using Photo Transport ­ A snapshot with an aspect ratio of 4:3 3 Creating a Dynamic Photo Image 4. Use [4] and [6] to select the built-in subject that you want to insert into the image and then press [SET]. * Only built-in subjects that can be inserted into other images will appear at this time. 5. [. . . ]