User manual CASIO EXILIM EX-ZR100

[. . . ] E Digital Camera User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ To go to "Getting the Most Out of Dynamic Photo" click here! Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] Use [8] and [2] to select "Yes", and then press [SET]. 104 Viewing Snapshots and Movies Copying a CS Group Image Use the following procedure to copy an image in a CS group to a location outside of the group. 1. While CS image playback is in progress or paused (toggle by pressing [SET]), press [2]. This will display the "CS Frame Edit" menu. 2. 4. Use [8] and [2] to select "Copy", and then press [SET]. Use [4] and [6] to display the image you want to copy. Use [8] and [2] to select "Copy", and then press [SET]. NOTE · The functions below cannot be performed on snapshots inside a CS group. Before using either of these functions, perform the above procedure to copy the image first. White Balance, Brightness, Trimming, Rotation, Resize 105 Viewing Snapshots and Movies Zooming an On-screen Image 1. 2. In the PLAY mode, use [4] and [6] to scroll through the images until the one you want is displayed. Slide the zoom controller towards z ([) to zoom. Zoom factor Image area You can use [8], [2], [4], and [6] to scroll the zoomed image on the monitor screen. Slide the zoom controller towards w to unzoom the image. ­ When monitor screen contents are turned on, a graphic in the lower right corner of the screen shows what part of the zoomed image is currently displayed. ­ To exit the zoom screen, press [MENU]. ­ Though the maximum image zoom factor is 8X, Current display area certain image sizes may not allow zooming up to the full 8X. · Pressing [SET] will lock the current zoom factor for the on-screen image. You can then use [4] and [6] to scroll between images, using the same zoom factor. Pressing [SET] again will unlock the zoom factor and allow you to use [8], [2], [4] and [6] to move around the currently displayed images. This function cannot be used while viewing CS group images or movies. Also, CS group images and movies will not appear when you are scrolling images with [4] and [6]. Displaying the Image Menu 1. In the PLAY mode, slide the zoom controller towards w (]). Use [8], [2], [4] and [6] to move the selection boundary around the image menu. To view a particular image, use [8], [2], [4], or [6] to move the selection boundary to the image you want and then press [SET]. · In the case of a movie or a continuous shutter (CS) file, the first frame of the file will be displayed. Boundary 106 Viewing Snapshots and Movies Viewing Snapshots and Movies on a TV Screen 1. Use the AV cable that comes with the camera to connect it to the TV. AV cable (bundled) Terminal cover TV Video Audio Yellow White Red [USB/AV] port AUDIO IN jack (red) AUDIO IN jack (white) VIDEO IN jack (yellow) Making sure that the 6 mark on the camera is aligned with the 4 mark of the AV cable connector, connect the cable to the camera. · Make sure that you insert the cable connector into the USB/AV port until you feel it click securely into place. Failure to insert the connector fully can result in poor communication or malfunction. · Note that even while the connector is fully inserted, you still will be able to see the metal part of the connector as shown in the illustration. · Make sure that the camera is turned off before plugging in or unplugging the cable. [. . . ] In the REC mode, compose the image and press the shutter button to shoot a standard snapshot. You will insert the built-in subject into the snapshot you shoot here. Step 2: Create the Dynamic Photo image. Now simply insert a built-in subject into the snapshot or movie you shot in step 1 to create your own original Dynamic Photo image. 1. Perform the following operation on the camera [MENU] * PLAY tab * "Dynamic Photo". 3. Use [4] and [6] to select the background image you want and then press [SET]. Select the image you want to use as the background. Here, select the image you recorded in step 1 of this procedure. * Only images that are able to be used as background images will appear for selection at this time. · Only an image that satisfies the following conditions can be used as a background image. [. . . ]