User manual CASIO EXILIM EX-Z120

[. . . ] E Digital Camera EX-Z120 User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/. K808PCM1DKX INTRODUCTION INTRODUCTION Unpacking Check to make sure that all of the items shown below are included with your camera. [. . . ] Use [ ] and [ ] to select the setting you want, and then press [SET]. To do this: Display images on the monitor screen for about one second immediately after they are recorded Do not display images immediately after they are recorded Select this setting: On Off 121 OTHER RECORDING FUNCTIONS Function Flash Focus White Balance ISO AF Area Metering Self-timer Flash Intensity Digital Zoom Setting when camera is turned off On Off Auto Auto Auto Auto Spot Multi Off 0 On Last Auto Focus position that was in effect before you switched to manual focus Wide 1. Select the "REC" tab, select "Memory", and then press [ ]. 3. Use [ ] and [ ] to select the item you want to change, and then press [ ]. 4. Use [ ] and [ ] to select the setting you want, and then press [SET]. To do this: Turn on mode memory so settings are restored at power on Turn off mode memory so settings are initialized at power on Select this setting: On Off MF Position Zoom Position* * Only the optical zoom position is remembered. 122 OTHER RECORDING FUNCTIONS IMPORTANT!· Note that BEST SHOT mode settings take priority over mode memory settings. If you turn the camera off while in the BEST SHOT mode, all settings except for "Zoom Position" will be configured according to the BEST SHOT sample scene when you turn it back on again, regardless of mode memory on/off settings. Specifying ISO Sensitivity You can change the ISO sensitivity setting for better images in places where lighting is dim or when you are using faster shutter speeds. · ISO sensitivity is expressed in terms of values that originally indicated the sensitivity to light for photographic film. A larger value indicates higher sensitivity, which is better for recording when available lighting is dim. 1. Select the "Quality" tab, select "ISO", and then press [ ]. 3. Use [ ] and [ ] to select the setting you want and then press [SET]. To get this: Automatic sensitivity selection Lower sensitivity Select this setting: Auto ISO 50 ISO 100 ISO 200 Higher sensitivity ISO 400 123 OTHER RECORDING FUNCTIONS IMPORTANT!· Under certain conditions, a high shutter speed in combination with a high ISO sensitivity setting can cause digital noise (graininess), which makes an image appear rough. For clean, good-quality images, use the lowest ISO sensitivity setting possible. · Using a high ISO sensitivity setting along with the flash to shoot a nearby subject may result in improper illumination of the subject. · "Auto" ISO sensitivity always is used for movie recording, regardless of the current ISO sensitivity setting. NOTE · You can use the key customization feature (page 120) to configure the camera so the ISO sensitivity setting changes whenever you press [ ] and [ ] while in a REC mode. Selecting the Metering Mode The metering mode determines what part of the subject is metered for exposure. You can use the following procedure to change the camera's metering mode. 1. Select the "Quality" tab, select "Metering", and then press [ ]. 3. Use [ ] and [ ] to select the setting you want, and then press [SET]. 124 OTHER RECORDING FUNCTIONS Multi (Multi pattern) Multi (Multi pattern) metering divides the image into sections and measures the light in each section for a balanced exposure reading. The camera automatically determines shooting conditions according to the measured lighting pattern, and makes exposure settings accordingly. This type of metering provides error-free exposure settings for a wide range of shooting conditions. Center Weighted Center weighted metering measures light concentrating on the center of the focus area. Use this metering method when you want to exert some control over exposure, without leaving settings totally up to the camera. [. . . ] Approximately 25 minutes with built-in memory After Recording . . . . . . . . . . . . . . . Approximately 30 seconds maximum per image 240 APPENDIX Monitor Screen . . . . . . . . . . . . . . . . . . 2. 0-inch TFT color LCD 84, 960 pixels (354 × 240) Viewfinder . . . . . . . . . . . . . . . . . . . . . . . . . . Monitor screen and optical viewfinder Timekeeping Functions . . . . [. . . ]