User manual CASIO FX-9860GSD

[. . . ] E fx-9860G SD fx-9860G User's Guide http://world. casio. com/edu/ GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U. S. A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Perform the following key operations from the statistical data list. 3(TEST) 5(ANOV) The following is the meaning of each item in the case of list data specification. selects One-Way ANOVA or Two-Way ANOVA (number of levels) Factor A . . . . . . . . . . . . . . . . . . . . . . . category list (List 1 to 26) Dependnt . . . . . . . . . . . . . . . . . . . . list to be used for sample data (List 1 to 26) Save Res . . . . . . . . . . . . . . . . . . . . first list for storage of calculation results (None or List 1 to 22)*1 Execute . . . . . . . . . . . . . . . . . . . . . . . executes a calculation or draws a graph (Two-Way ANOVA only) The following item appears in the case of Two-Way ANOVA only. category list (List 1 to 26) After setting all the parameters, use c to move the highlighting to "Execute" and then press one of the function keys shown below to perform the calculation or draw the graph. Calculation results are displayed in table form, just as they appear in science books. *1 [Save Res] saves each vertical column of the table into its own list. The leftmost column is saved in the specified list, and each subsequent column to the right is saved in 20050401 the next sequentially numbered list. Up to five lists can be used for storing columns. You can specify an first list number in the range of 1 to 22. 6-5-23 Tests Calculation Result Output Example One-Way ANOVA Line 1 (A) . . . . . . . . . . . . . . . . . . . . Factor A df value, SS value, MS value, F value, p-value Line 2 (ERR) . . . . . . . . . . . . . . . Error df value, SS value, MS value Two-Way ANOVA Line 1 (A) . . . . . . . . . . . . . . . . . . . . Factor A df value, SS value, MS value, F value, p-value Line 2 (B) . . . . . . . . . . . . . . . . . . . . Factor B df value, SS value, MS value, F value, p-value Line 3 (AB) . . . . . . . . . . . . . . . . . . Factor A × Factor B df value, SS value, MS value, F value, p-value *Line 3 does not appear when there is only one observation in each cell. Error df value, SS value, MS value F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F value p-value degrees of freedom sum of squares mean squares With Two-Way ANOVA, you can draw Interaction Plot graphs. The number of graphs depends on Factor B, while the number of X-axis data depends on the Factor A. The Y-axis is the average value of each category. You can use the following graph analysis function after drawing a graph. [. . . ] Load a new set of four batteries, making sure that their positive (+) and negative (­) ends are facing in the proper directions. Turn the calculator front side up and slide off its case. Next, press o to turn on power. # Power supplied by memory back up battery while the main power supply batteries are removed for replacement retains memory contents. # Do not leave the calculator without main power supply batteries loaded for long periods. Doing so can cause deletion of data stored in memory. [. . . ]