User manual CASIO HR-8TE

[. . . ] Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. [. . . ] takes no responsibility for any damages, lost profits, or claims by third parties arising from the deletion of recorded data due to malfunction, repair, or for any other reason. Record Using the RECORDER Button Memory Capacity · You can record approximately 5, 000 notes in digital piano memory. · The RECORDER button lamp will flash at high speed when memory runs low. · Recording stops automatically if the number of notes in memory exceeds the maximum. Each press of the RECORDER button cycles through the recording options in the sequence shown below. Lit Flashing Off Playback Standby Record Standby Normal Recorded Data · Keyboard play · Tone used · Pedal operations · Reverb and chorus settings (Track 1 only) · Tempo setting (Track 1 only) · Layer setting (Track 1 only) · Split setting (Track 1 only) · Temperament and base note settings (Track 1 only) · Octave shift setting (Track 1 only) E-14 Recording and Play Back To record to a specific track of a song After recording to either of the tracks of a song, you can record to the other track while listening to playback what you recorded in the first track. 4. 5. Start playing something on the keyboard. · Recording will start automatically. 1. Press the RECORDER button twice so its lamp is flashing. · This will cause the RECORDER button lamp and the lamp of the track you recorded to change from flashing to lit. · To play back the track you just recorded, press the SONG a button. 6. After you are finished recording or playing back, press the RECORDER button so its lamp goes out. · At this time the L lamp will flash to indicate that the digital piano is standing by for recording to Track 1. 2. While holding down the FUNCTION button, press the RECORDER (L) button or METRONOME (R) button to select the track you want to record. · Make sure that the indicator lamp for the record track is flashing. Track 1: L lamp Track 2: R lamp Example: Track 1 selected 3. Select the tone and effects (Track 1 only) you want to use in your recording. · Tone (page E-6) · Effects (page E-9) NOTE · If you want the metronome to sound while you are recording, configure the beat and tempo settings, and then press the METRONOME button. See "Using the Metronome" on page E-10 for more information. E-15 English To stop recording, press the SONG a button. Recording and Play Back To record to one track of a song while listening to the playback of the other track Playing Back from Digital Piano Memory 1. 1. Press the RECORDER button so its lamp is lit. Press the RECORDER button so its lamp is lit. NOTE 2. While holding down the FUNCTION button, press the RECORDER (L) button or METRONOME (R) button to select the track you want to play back while recording. Press the RECORDER button so its lamp is flashing. · This will cause the L lamp to flash. · When a song has something recorded in both tracks, you can turn off one track and play back just the other track, if you want. 2. Press the SONG a button. · This starts playback of the song and/or track you selected. 3. 4. NOTE While holding down the FUNCTION button, press the RECORDER (L) button or METRONOME (R) button to select the track you want to record. · Make sure that the indicator lamp for the record track is flashing. Example: To listen to playback of Track 1 as you record to Track 2 · You can change the tempo setting as a track is playing. (page E-8) bq Layer balance Song/Metronome Parameter Settings Operation Type (page E-18) B (+/­) C (0 to 9) Description Specifies the tempo of Music Library songs, the metronome, recording and playback, etc. (page E-10) Remarks · Always enter three digits when using the number keys (0 to 9) to input a value. Example: To input 90, enter 0, 9, 0 (leading zero required). · During recording, pressing + and ­ at the same time sets a value of 120. · Always enter two-digits when using the number keys (0 to 9) to input a value. Example: To input 8, enter 0, 8 (leading zero required). · This setting cannot be changed while recording. · This setting cannot be changed while recording. 7 Tempo (TEMPO) 20 to 255 Default: 120 8 Song select 01 to 60 (SONG SELECT) Default: 01 B (+/­) C (0 to 9) Selects a Music Library tune. (page E-12) bl Song volume bm Metronome 00 to 42 (SONG VOLUME) Default: 42 00 to 42 volume Default: 36 (METRONOME VOLUME) (METRONOME Default: 4 BEAT) B B Sets the volume level of Music Library playback. (page E-10) bn Metronome beat 0, 2, 3, 4, 5, 6 A Specifies the metronome beat. (page E-10) · The metronome beat setting cannot be changed while playback of a Music Library tune is in progress. E-20 Configuring Settings with the Keyboard Keyboard Parameter Settings ­12 to 0 to 12 Default: 0 B Operation Type (page E-18) Description Raises or lowers the tuning of the digital piano in semitone steps. [. . . ] · AC adaptor operating environment Temperature: 0 to 40°C Humidity: 10% to 90% RH · Output polarity: Included and Optional Accessories Use only accessories that are specified for use with this product. Use of unauthorized accessories creates the risk of fire, electric shock, and personal injury. Weld Lines Lines may be visible on the exterior of the product. These are "weld lines" that result from the plastic molding process. They are not cracks or scratches. Musical Instrument Etiquette Always be aware of others around you whenever using this product. [. . . ]