User manual CASIO JD-7000

[. . . ] E-15 Using the CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-16 To view the contents of a User's Guide (PDF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-16 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-17 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-18 Main Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-20 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10 General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-11 Getting Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Avoid watching 3D images for very long periods. Be sure to observe the following precautions when watching 3D images. + Take care about nearby people and objects. Viewing 3D images can interfere with distance judgment, so you should take care about nearby people and objects when extending your arms or making sudden movements. Failure to do so creates the risk of material damage and personal injury. Use 3D glasses when viewing 3D images. Watching 3D images without 3D glasses can cause eye fatigue. Always use the specified 3D glasses whenever viewing 3D images. You need to wear your glasses or any other devices you normally use for vision correction. If you normally wear glasses or contact lenses, you should be wearing them when you watch 3D images with the 3D glasses. Failure to do so creates the risk of eye fatigue or abnormal vision. E-6 Operating Precautions About the Light Source Unit The projector's light source unit uses a laser and LED. The life of the light source unit is rated at approximately 20, 000 hours. The actual life will depend on use conditions, the settings configured on the setup menu, and differences between each individual light source unit. The light source unit is warranted for the period noted on the warranty certificate or for 6, 000 hours, whichever comes first. The failure of the light source unit to light or a noticeable drop in light source unit brightness indicates the end of the light source unit's life. Contact your original dealer or authorized CASIO service center for replacement. Note that problems caused by unauthorized projector disassembly or modification are not covered by the warranty and are not eligible for repair by CASIO. Laser Precautions This projector is a Class 1 laser device that conforms with IEC 60825-1. Because of this, you should hold the sides of the projector as shown in the illustration whenever moving it. Stowing the Projector in the Carrying Bag Make sure the projector is no longer warm before stowing it in the carrying bag. Cleaning the Projector Periodically clean the projector exterior, lens, intake vents, and intake-exhaust vents on a regular basis. Dust and dirt tend to collect around the vents. Because of this, you should use a vacuum cleaner to clean away accumulated dust and dirt periodically. Continued use of the projector after dust has accumulated around the vents can cause overheating of internal components and lead to malfunction. E-9 Unpacking As you unpack the projector, check to make sure that all of the items listed below are present. DATA PROJECTOR Remote Controller (YT-120) Mini D-Sub Cable · · · · · · · · Test Batteries (AAA-size × 2) AC Power Cord Carrying Bag CD-ROM Setup Guide "Read this first" Sheet Warranty Wireless adapter (Provided with models equipped with USB ports only. ) E-10 General Guide CLASS 1 LASER PRODUCT XJ-H1600/XJ-H1650 [P] (Power) key Control panel Intake vents Indicators Brightness sensor Intake-exhaust vents Speaker Lens cover Projection lens Lens cover strap Focus ring Intake-exhaust vents Zoom ring Intake-exhaust vents Remote control signal receiver XJ-ST145/XJ-ST155 [P] (Power) key Control panel Intake vents Indicators Brightness sensor Intake-exhaust vents Speaker Lens cover Projection lens Intake-exhaust vents Focus ring Intake-exhaust vents Remote control signal receiver E-11 Getting Ready Loading Remote Controller Batteries Important! Be sure to use alkaline batteries only. *Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 1. Open the battery cover on the back of the remote controller. 2. Load two new batteries into the case, making sure that their positive (+) and negative (­) ends are facing correctly. 3. Close the battery cover on the back of the remote controller. Replacing Remote Controller Batteries Open the battery cover on the back of the remote controller, replace the old batteries with new ones, and then close the battery cover. Important! To avoid running down the batteries, store the remote control unit so its buttons are not pressed inadvertently. Setting Up the Projector Place the projector onto a table, desk, or stand that is level and firm, making sure you allow enough room around it. Best results can be obtained when the projector is pointed directly at the screen, and not at an angle. XJ-H1600/XJ-H1650 Screen XJ-ST145/XJ-ST155 Screen The projector can be configured for projection from the back of a screen. For details, see the User's Guide on the CD-ROM that comes with the projector. E-12 Getting Ready Setup Precautions Use a conveniently located power outlet that you can reach easily when you need to unplug the projector. [. . . ] Unplug the AC power cord and wait for at least 10 minutes. Plug the power cord back in and turn the projector back on again. If normal operation does not resume after you perform the above steps, take the projector to your retailer or authorized CASIO service center. E-19 Main Specifications Model Name Brightness (ANSI Lumens) Environment XJ-H1600/XJ-H1650 3500 XJ-ST145 2500 XJ-ST155 3000 Operating Temperature: 5 to 35°C (41 to 95°F) Operating Humidity: 20 to 80% (non-condensation) Operating Altitude: 0 to 3, 000 meters (0 to 10, 000 feet) above sea level Requirements 100-240V AC, 50/60Hz, 5. 1A-2. 2A 400 (W) × 323 (D) × 106 (H) mm (15. 7" × 12. 7" × 4. 2") Approximately 7. 1kg (15. 7Ibs) Requirements 100-240V AC, 50/60Hz, 5. 1A-2. 2A 420 (W) × 323 (D) × 106 (H) mm (16. 5" × 12. 7" × 4. 2") Approximately 7. 1kg (15. 7Ibs) Power Approximate Dimensions Weight Specifications are subject to change without notice. B E-20 GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U. S. A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ]