User manual CASIO LK-35

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Pressing the PAUSE button again resumes play from the point where it was paused. 1 While a tune is playing or paused, hold down the FF button to skip forward at high speed. · The fast forward operation skips forward one measure at a time. · The measure and beat numbers on the display change while the fast forward operation is being performed. To fast reverse 1 While a tune is playing or paused, hold down the REW button to skip in a reverse direction at high speed. · The fast reverse operation skips back one measure at a time. · The measure and beat numbers on the display change while the fast reverse operation is being performed. Measure number Beat number 2 Releasing the FF button starts song playback from the measure whose number is shown on the display. NOTE · Fast forward does not work while tune play is stopped. Measure number Beat number Looping a Musical Phrase You can select one or more measures and "loop" them, which means that they play again and again until you stop playback. 2 Releasing the REW button starts song playback from the measure whose number is shown on the display. 1 NOTE · Fast reverse does not work while tune play is stopped. · Certain playback conditions can cause it to take some time before fast reverse starts after you press the REW button. While the tune is playing, press the REPEAT button while the measure you want to start from is playing. · This causes the repeat indicator to flash on the display, and displays the measure number of the start measure. 2 When playback is within the measure you want to specify as the end of the loop, press the REPEAT button again. · This displays the measure number of the end measure, and starts repeat play of the loop. · To cancel repeat play of a loop, press the REPEAT button again so the repeat indicator is not displayed. E-21 Playing a Built-in Tune To change the melody tone Using the PIANO BANK Button Pressing the PIANO BANK button provides instant access to piano tones and piano tune selection. Initial Piano Bank Setting Tone: 000 STEREO PIANO 1 Press the TONE button. To use the piano bank Indicator appears 1 Press the PIANO BANK button. 2 Find the tone you want in the TONE List, and then use the number buttons to input its three-digit number. Example: To select "057 VIOLIN", input 0, then 5, then 7. · You can select any one of the keyboard's 264 built-in tones. Indicator appears Viol in NOTE · You can also use the [+] and [­] buttons to change the melody tones. · For two-hand tunes (Piano Bank tunes), the same tone is applied for both the left and right hand parts. · Specifying the tune number for the same tune that is currently selected returns the melody tone to the default setting for that tune. 2 3 Now try playing something on the keyboard. · The notes you play sound with a piano tone. If you want to playback the built-in tune, press the PLAY/STOP button. · This causes the currently selected tune to play in an endless loop. · To stop playback, press the PLAY/STOP button again. Using the SMF Data on the Bundled CD-ROM The CD-ROM that comes bundled with the keyboard contains demos as well as 25 tunes (SMF data) that you can use for step lessons. It also contains PDF format files that contain the sheet music of the included tunes. The more segments that appear, the higher your points. Example: 50 points Key light NOTE · Note length is not indicated when you are using twohand tunes with 3-step lesson Steps 1 and 2. As soon as you press a lit key, it goes out and the next key to be played starts to flash. · Note length is indicated by the key light system when you use a two-hand tune with Step 3. In this case, the next key to be pressed does not flash when you press a lit key and the next finger number does not appear on the display. Only the current finger number is shown. Timing Indicator: In the Evaluation Mode, the configuration of the star changes with each note to let you know how your timing is. The more stars, the better your timing. Evaluation Results 3-step Lesson Tempo Setting Use the procedure under "Adjusting the Tempo" on page E-20 to adjust the tempo for 3-step lesson play. After you finish playing, the keyboard calculates an evaluation of your total performance, from beginning to end, and displays your total score on the monitor screen. The greater the score, the higher your evaluation is. Evaluation Rank Display Messages Display Message "Bravo!" "Great!" "Not bad!" "Again!" Dynamic Marks The dynamic marks listed below appear on the display while tunes are playing. [. . . ] Except for your own, personal use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws. · IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. · The contents of this manual are subject to change without notice. I User Maintenance · Never use benzene, alcohol, thinner, or other chemical agents to clean the product. · To clean the product or its keyboard, wipe with a soft cloth moistened in a weak solution of water and a mild neutral detergent. [. . . ]