User manual CASIO PRO TREK PRG-80T MODULE 2894

[. . . ] MO0412-EA Operation Guide 2894 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully and keep it on hand for later reference when necessary. · Frequent display illumination can run down the battery quickly and require charging. The following guidelines give an idea of the charging time required to recover from a single illumination operation. [. . . ] · All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing D. To measure times with the stopwatch Elapsed Time C C Start Stop Split Time C A Start Split (sp displayed) Two Finishes C A Start Split First runner finishes. Display time of first runner. L L L C Re-start C Stop A Clear L L L A Split release C Stop A Clear L L L C Stop Second runner finishes. A Split release Display time of second runner. A Clear L L L 6 Operation Guide 2894 Countdown Timer Minutes Seconds Alarms You can set a countdown timer start time in the range of one minute to 60 minutes. An alarm sounds when the countdown reaches zero. An auto-repeat feature causes the countdown to restart automatically when the end of a countdown is reached, and a progress beeper signals the progress of the countdown. · All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing D. Alarm on indicator Hourly time signal on indicator Alarm number Timekeeping Mode time Configuring the Countdown Timer The following are the settings you should configure before actually using the countdown timer. · Countdown start time · Auto-repeat on/off · Progress beeper on/off Timekeeping Mode time Alarm time (Hour : Minutes) You can set five independent daily alarms. When an alarm is turned on, the alarm tone sounds when the alarm time is reached. You can also turn on an Hourly Time Signal, which will cause the watch to beep twice every hour on the hour. · The alarm number (AL1 through AL5 ) indicates an alarm screen. SIG is shown when the Hourly Time Signal screen is on the display. · When you enter the Alarm Mode, the data you were viewing when you last exited the mode appears first. · All of the operations in this section are performed in the Alarm Mode, which you enter by pressing D. Countdown start time You can set a countdown start time in the range of one minute to 60 minutes, in one-minute increments. To set an alarm time 1. In the Alarm Mode, use C and A to scroll through the alarm screens until the one whose time you want to set is displayed. C AL1 AL2 AL3 Auto-repeat Whenever zero is reached, the watch beeps and auto-repeat automatically restarts the countdown from the countdown start time you set. When the countdown reaches zero while auto-repeat is turned off, the watch will beep and then display the countdown start time (without restarting the countdown). Auto repeat will repeat up to 10 times. A AL5 SIG AL4 Progress Beeper When the progress beeper is turned on, the watch beeps at minute 10, 5, 4, 3, 2, and 1, of the countdown, and at second 50, 40, 30, 20, 10, 5, 4, 3, 2, and 1 of the final minute of the countdown. To configure countdown start time and auto repeat settings 1. While the countdown start time is on the display in the Countdown Timer Mode, hold down E until the minute setting of the countdown start time starts to flash, which indicates the setting screen. · If the countdown start time is not displayed, use the procedure under "To use the countdown timer" to display it. Press D to toggle between the countdown starting time setting screen and the auto repeat setting screen. 2. Hold down E until the hour setting of the alarm time start to flash, which indicates the setting screen. · This automatically turns on the alarm. Press D to move the flashing between the hour and minute settings. While a setting is flashing, use C (+) and A (­) to change it. [. . . ] After the settings are the way you want, press E to exit the setting screen. Place the watch on a level surface, and position it so that its 12 o'clock position points north (as measured with another compass). Press A to start the calibration operation. · --- is shown on the display while calibration is being performed. [. . . ]