User manual CASIO PS-20

[. . . ] USER'S GUIDE GUÍA DEL USUARIO P PS20-ES-1 PS20_ES_cover. p65 Page 1 02. 2. 4, 7:11 PM Adobe PageMaker 6. 5J/PPC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] 2. Press METRONOME to start the metronome. Set the beat of the metronome. · While holding down the CONTROL button, press the keyboard key that corresponds to the beat setting you want to select. · A note does not sound when you press a keyboard key while holding down CONTROL. · The first value of the beat can be set to a value of 2 through 6. The bell (indicating the first beat of a measure) does not sound while a value of 0 is specified. All beats are indicated by a click sound. This setting lets you practice with a steady beat, without worrying about how many beats there are in each measure. 1. While holding down the CONTROL button, press the keyboard key that corresponds to the metronome volume setting you want to select. · A note does not sound when you press a keyboard key while holding down CONTROL. · You can set a value from 1 to 3. NOTE · The metronome volume is automatically set to 2 whenever you turn on the digital piano power. 3. Change the tempo setting as described below. · A note does not sound when you press a keyboard key while holding down CONTROL. · While holding down the CONTROL button, press keyboard key A 3 (­) to decrease tempo or B 3 (+) to increase it. Holding down either keyboard key changes the setting at high speed. E-16 424A-E-018A PS20_E_08-16. p65 Page 16 02. 2. 4, 7:12 PM Adobe PageMaker 6. 5J/PPC Using the Memory This section describes how to record keyboard play to memory and playback data from memory. Recording To record notes from the keyboard PREPARATION · Select the tone and effects you want to start with. · If you want to use the metronome during recording, start the metronome. Use the procedure under "Using the Metronome" on page E-16 to set the beat and the tempo. About the Memory Memory Capacity Memory can hold up to 2, 500 notes (one song). · Recording stops automatically and the indicator above the RECORD button goes out whenever memory becomes full. 1. Press the RECORD button to put the digital piano into record standby. · The indicator above the RECORD button flashes, which indicates record standby. · You can also change the metronome's beat setting at this time. · If you want the metronome to sound while you are recording, press the METRONOME button here to start the metronome. Recorded Data The following is a list of the data that can be recorded in memory once recording starts. · Anything you played on the keyboard (Received MIDI data is not recorded. ) · Tone settings and any tone setting changes · Beat setting used during recording · Pedal operations 2. Play something on the keyboard to start recording. · What you play sounds from the speakers and is recorded into memory. · You can also start recording by pressing the START/ STOP button. In this case, a blank space is inserted in memory from the point that you press the START/ STOP button up to the point you start to play on the keyboard. · When you start recording, the indicator above the RECORD button stops flashing and remains lit. Recorded Data Storage This digital piano has a lithium battery to supply power to retain memory contents even while power is off. * The life of the lithium battery is five years after the date of manufacture of the digital piano. Be sure to contact your CASIO Service Provider about having the lithium battery replaced every five years. * Never turn off the digital piano power while a record operation is in progress. 3. IMPORTANT! · Recording new data to a song memory area automatically deletes any data previously stored in that song memory area. · Turning off power while a record operation is in progress deletes anything recorded up to that point. [. . . ] There is no change when the value of the data entry MSB is 40H(0). 02. 2. 4, 7:13 PM Pitch Bend Sensitivity # RPN MSB = 00H RPN LSB = 00H Data Entry MSB = mmH mm . . . . . Pitch Bend Sensitivity = 00H to 18H (0 to 24 semitones) Recognition The data entry LSB is always ignored. Filter/AMP Envelope Decay Time NRPN MSB = 01H NRPN LSB = 64H Data Entry MSB = mmH Pitch Bend Change # Format Byte 1 EnH Byte 2 llH Byte 3 mmH n . . . . . . . . . . Voice Channel Number = 0H to FH (Ch1 to Ch16) ll . . . . . . . . . . Pitch Bend Change LSB = 00H to 7FH mm . . . . . [. . . ]