User manual CASIO PS-3000

[. . . ] ES USER'S GUIDE GUÍA DEL USUARIO PS3000-ES-1 PS3000_es_cover. p65 1 03. 10. 8, 2:22 PM NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Change the transpose setting to 0, or turn the digital piano power off and then back on again. Correct the tuning setting, or turn the digital piano power off and then back on again. Turn off the digital piano power and then check to make sure that the pedal plug is securely connected to the piano's PEDAL jack. Move VOLUME knob more towards the MAX side. Disconnect the headphones from the piano. Contact your CASIO Service Provider for replacement of the lithium battery. Change the Keyboard Channel settings so they are identical. Reference Page E-12 Page E-11 Page E-24 Page E-19 Keyboard out of tune. 1. Transpose is set to a value other than 0. Incorrect tuning setting Page E-20 Pedal effect continues to be applied even though pedals are not pressed. No sound produced by demo tune play. Problem with the connection between the pedals and piano. Page E-11 1. Headphones connected to the piano. Page E-12 Page E-11 Page E-31 Memory contents deleted. Lithium battery is dead. No sound produced by connected external MIDI sound source when the digital piano keys are pressed. 1. The digital piano Keyboard Channel does not match the Keyboard Channel of the MIDI sound source. Volume or expression setting of the external sound source is set to 0. Page E-22 2. Change the volume or expression setting of the external sound source to an appropriate value. See the documentation that comes with the external sound source. E-26 PS3000_e_26_31. p65 26 03. 10. 8, 2:22 PM 417A-E-028B Assembly Instructions Caution · This stand should be assembled by two people working together. · When assembling the stand, you should have the piano standing up with its back facing downwards, as shown in Figure 3. · Do not remove the tape securing the keyboard cover in place until assembly is complete. Removing the tape can cause the keyboard cover to open and close during assembly, creating the risk of personal injury to your hands and fingers. · During assembly, be sure to exercise sufficient caution to avoid personal injury. · Before starting assembly of the stand, divide the polystyrene foam packing material into four parts (Figure 2). Figure 2 IMPORTANT! · Be sure to assemble the stand on a flat surface. · This stand does not include any of the tools required to assemble it. You should have a large Phillips head (+) screwdriver on hand for assembly. [. . . ] Reconocimiento La recepción del mensaje del controlador de reposición completa ocasiona que los controladores siguientes se reposicionen. Nombre de controlador Perilla de modulación Controlador de expresión Retención 1 Portamento Sostenuto Suave NRPN RPN Cambio de inflexión de altura tonal Valor de reposición vvH = 00H vvH = 7FH vvH = 00H vvH = 00H vvH = 00H vvH = 00H msb = 7FH, lsb = 7FH msb = 7FH, lsb = 7FH llH mmH = 00H 40H Cambio de programa Formato 1er. Número de programa = 00H a 7FH Envío Los mensaje de cambio de programa son enviados cuando selecciona un sonido en el instrumento. A-12 PS3000_s_MIDI Data. p65 12 03. 10. 22, 2:54 PM 417A-E-078A Formato de datos MIDI Desactivación de nota completa Formato 1er. Número de canal de voz = 0H a FH (canal 1 al canal 16). [. . . ]