User manual CASIO PX-410R

[. . . ] E USER'S GUIDE PX410/575E1B TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] A setting of zero specifies no change in output volume in accordance with keyboard pressure. Sin Vib. T Value Sin Tri Sau Sqr Meaning Sine Wave Triangle Wave Sawtooth Wave Square Wave yp e Waveform 32 TchSen se I Reverb Send (Range: 000 to 127) This parameter adjusts reverb. 127 Rvb This parameter adjusts chorus. Send I Vibrato Delay (Range: ­64 to 00 to +63) Specifies the amount of time before vibrato starts. I Chorus Send (Range: 000 to 127) 00 V i bDe l a I Vibrato Rate (Range: ­64 to 00 to +63) Rate (speed) of the vibrato effect y 112 Cho I DSP Line (Settings: On, Off) Send This parameter controls whether or not the DSP effect is used. 02 V i b . Ra t e I Vibrato Depth (Range: ­64 to 00 to +63) Depth of the vibrato effect On DSP L i ne 12 V i bDe I Octave Shift (Range: ­2 to 0 to +2) Up/down octave shift p th - 1 Oc t Sh i f t I Level (Range: 000 to 127) This parameter controls the overall volume of the tone. The greater the value, the greater the volume. Setting a level of zero means that the tone does not sound at all. 096 Leve l E-47 Synthesizer Mode DSP Settings Use the DSP editing screen to select the DSP type and to edit parameters. Storing a User Tone In Memory The following procedure shows how to store a user tone in memory. Once a tone is stored, you can call it up just as you do with a preset tone. 1 2 Select a tone, press the SYNTH button, and then configure parameter settings. After everything is the way you want, press the [ ] CURSOR button once. · This advances to the DSP parameter editing screen. · Pressing the [ ] CURSOR button returns to the Synthesizer Mode parameter screen. To name a user tone and store it in memory 1 This setting specifies DSP parameters. For details, see "DSP Parameters" on page E-26, the separate Appendix E, and the "algorithmlist_e. pdf" file in the "English" folder on the CD-ROM that comes with your digital piano. Select a preset tone to use as the basis for the user tone, press the SYNTH button to enter the Synthesizer Mode, and make the parameter settings you want. After making parameter settings to create the user tone, press [ ] CURSOR button twice. Use [+] and [­] buttons or the number buttons to change the user area tone number on the display until the one where you want to store the tone is shown. · You can select any tone number from 700 to 799. 2 3 NOTE · If you store an original tone with the DSP line turned on (page E-49), simply recalling the tone automatically changes the DSP line, DSP type, and DSP parameter settings. This simplifies the recall of original tones that include a DSP effect. 701 User Tone Creation Hints The following hints provide helpful advice on making user tone creation a bit quicker and easier. Use a preset tone that is similar to the one you are trying to create. Whenever you already have a rough idea of the tone you are trying to create, it is always a good idea to start with a preset tone that is similar. I Experiment with various different settings. There are no real rules about what a tone should sound like. Let your imagination run free and experiment with different combinations. You may be surprised at what you can achieve. 4 After the tone name is the way you want, press the [ ] CURSOR button to store the tone. · Use the [+] and [­] buttons to scroll through letters at the current cursor location. · Use the [ ] and [ ] CURSOR buttons to move the cursor left and right. · See the page E-87 for information about inputting text. 5 Press [ ] CURSOR button to save the user tone. · This will display a confirmation message asking whether you really want to save the data. · The message "Complete" appears momentarily on the display, followed by the tone or rhythm selection screen. · To abort the save operation at any time, press the SYNTH button or the EXIT button to exit the Synthesizer Mode. Pressing the SYNTH button again (before selecting another tone) returns to the Synthesizer Mode with all of your parameter settings still in place. E-48 Registration Memory Registration Memory Features Registration memory lets you store up to 32 digital piano setups (4 sets × 8 banks) for instant recall whenever you need them. [. . . ] The memory card is not inserted correctly into the card slot. There is not enough space available in the area into which you are trying to import the data. You are trying to use a memory card whose capacity is not supported by this digital piano. After transferring song data from my computer, playback stops part way through. [. . . ]