User manual CASIO QW-373

[. . . ] There is also a "­ ­" setting which means that the match time is unlimited. · Holding down the C or A button scrolls at high speed. After the time setting is the way you want, press the R button to exit the setting screen. · Press the C button to start timing of the match in the upper and lower display areas ("Football" flashes on the display). [. . . ] · When the timer sequence reaches the end of the final interval, it restarts from the beginning of the first interval. CHART 0 a (a) To time a match BUTTON OPERATION Current time Number of repeats Timer number Timer start time DISPLAY PM NET TIME START STOP START STOP RESET CHART 0 a (a) (a) (Stoppage time) b (a + b) Example: Timer 1 20'00" Timer 2 10'00" Timer 3 05'00 Repeat 2 CHART Timer 1, Repeat 1 start Timer 1 end, Timer 2 start Timer 2 end, Timer 3 start 0 a (a) (a) (Stoppage time) b (a + b) BUTTON OPERATION BUTTON OPERATION Timer 3 end Timer 2 end, Timer 3 start Timer 1 end, Timer 2 start Timer 3 end, Timer 1 start DISPLAY DISPLAY CARE OF YOUR STOPWATCH After stopping a net time operation by pressing C, you can resume it by pressing C again. LAP/SPLIT TIMES START 1ST LAP STOP 2ND LAP 3RD LAP RESET To set an interval start time · This stopwatch is water resistant up to five bars (atmospheres), which means you can use it in the rain or in areas where splashing water is present. Never, however, operate the buttons of the stopwatch while it is immersed in water. · You should have the rubber seal that keeps out water and dust replaced every 2 to 3 years. · Should moisture appear inside the stopwatch, have it checked immediately by your dealer or a CASIO distributor. 0 CHART Football Stopwatch Mode Counter Mode Alarm Mode Timer Mode a (a) b (a + b) c (a + b + c) (t) Reset Timer Selection SPECIFICATIONS Accuracy at a normal temperature (TIME): ±30 seconds per month (STOPWATCH): 99. 9988% Display capacity: · Time Display: Hour, minutes, seconds, am/pm, year, month, day and day of the week Calendar system: Pre-programmed until the year 2099 · Stopwatch Display: Measuring capacity: (Total elapsed time display) 9 hours 59 minutes 59. 999 seconds (Lap time display) 59 minutes 59. 999 seconds (Split time display) 9 hours 59 minutes 59. 999 seconds Measuring unit: 1/1000 second Measuring modes: Net time, lap time, split time, 1st-100th place time, lap counter (up to 99) Memory capacity: 2 sets of 100 records each Timer 10 intervals Measuring capacity: 59 minutes 59 seconds Measuring unit: 1 second Number of repeats: 100 Beeper duration: 10 seconds Alarm Number of alarms: 12 Beeper duration: 10 seconds Setting unit: 1 minute Counter Standard Counter: 0 to 99999 Stopwatch Counter: 0 to 99999 Measuring capacity: 59 minutes 59 seconds Dual Counter: 0 to 99999 Football Stopwatch Measuring capacity: 59 minutes 59 seconds Measuring unit: 1 second Beeper duration: 10 seconds Battery: One lithium battery (type: CR2032) Approx. 5 years continuous operation on type CR2032 (includes an average of 30 presses of button per day. ) Operating Temperature: 0°C to 40°C (32°F to 104°F) 1ST SPLIT (a) 2ND SPLIT (a+b) 3RD SPLIT (a+b+c) BUTTON OPERATION Timer Interval Setting Repeat Setting DISPLAY · A sticker is affixed to the glass of this stopwatch when you purchase it. Be sure to remove the sticker before using the stopwatch. · Depending on its model, the configuration of your stopwatch may differ somewhat from that shown in the illustration. MULTIPLE FINISHING TIMES Example : To record the times of 100 different runners. START 1ST RUNNER FINISHES 2ND RUNNER FINISHES 99TH RUNNER FINISHES 100TH RUNNER FINISHES RESET 1. In the Timer Mode, hold down the R button for about 2 seconds until the displayed interval time starts to flash. Use the C and A buttons to scroll through the 10 interval times until the one you want to change is displayed. · Interval timers count down in sequence from Timer 1 to Timer 10. In the Alarm Mode, use the C button to display the alarm (AL 1 to AL 12) you want. Press the A button to toggle the alarm on or off. To turn all alarms off SPLIT TIME AND LAP TIME Split time (SPLIT) is the time elapsed from the start to a specific point. Lap time (LAP) is the time elapsed from one point to another or for one lap around a track. START 1ST SPLIT 2ND SPLIT 3RD SPLIT START 1ST LAP 2ND LAP 3RD LAP USING THE RECALL MODE You can use the recall mode to view data in stopwatch memory. · There is enough memory to store a total of up to 200 records, divided between two record groups of 100 each. If you record 100 times, the 100th time will not be stored in memory until you reset the stopwatch to all zeros. · Starting a new stopwatch elapsed time operation will cause the older of the two record groups to be deleted automatically in order to make room for a new group of records. · There is also a FAST LAP record that displays the fastest lap from among all of the lap times currently in memory. · Record 1 (the newest record) will always be displayed first whenever you press the R button to switch from the Stopwatch Mode to the Recall Mode. · In the Recall Mode, each press of the B button will toggle the display between record group 1 and record group 2. · Lap time records in memory can be recalled while an elapsed time operation is in progress or stopped. [. . . ] After the setting is the way you want, press the R button to exit the setting screen. · The alarm will not sound if the time on a flashing setting screen arrives. · The stopwatch will exit the setting screen automatically if you do not perform any operation for two or three minutes. · Displaying the setting screen for an alarm will cause that alarm to turn on. USING THE STOPWATCH The stopwatch beeps to signal C and A button operations. USING THE COUNTER · The stopwatch is equipped with three types of counters, which can be used to maintain a count from 0 to 99, 999. [. . . ]