User manual CASIO QX-2328

[. . . ] E-15 Using the CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-16 To view the contents of a User's Guide (PDF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-16 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-17 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-18 Main Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-20 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10 General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10 Getting Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Always use the specified 3D glasses whenever viewing 3D images. You need to wear your glasses or any other devices you normally use for vision correction. If you normally wear glasses or contact lenses, you should be wearing them when you watch 3D images with the 3D glasses. Failure to do so creates the risk of eye fatigue or abnormal vision. E-6 Operating Precautions About the Light Source Unit The projector's light source unit uses a laser and LED. The life of the light source unit is rated at approximately 20, 000 hours. The actual life will depend on use conditions, the settings configured on the setup menu, and differences between each individual light source unit. The light source unit is warranted for the period noted on the warranty certificate or for 6, 000 hours, whichever comes first. The failure of the light source unit to light or a noticeable drop in light source unit brightness indicates the end of the light source unit's life. Contact your original dealer or authorized CASIO service center for replacement. Note that problems caused by unauthorized projector disassembly or modification are not covered by the warranty and are not eligible for repair by CASIO. Laser Precautions This projector is a Class 1 laser device that conforms with IEC 60825-1. This projector has a built-in laser module. Disassembly or modification is very dangerous and should never be attempted. Any operation or adjustment not specifically instructed by the user's guide creates the risk of hazardous laser radiation exposure. Bottom E-7 Operating Precautions Other Precautions This projector is made of precision components. Continued use of the projector after dust has accumulated around the intake vents can cause overheating of internal components and lead to malfunction. Certain operating conditions also can cause dirt and dust to accumulate around the projector's exhaust vents and airflow vents. If this happens, use the same procedure as that described above to clean the exhaust vents and airflow vents. E-9 Unpacking As you unpack the projector, check to make sure that all of the items listed below are present. · · · · · · · · DATA PROJECTOR Remote Controller (YT-120) Test Batteries (AAA-size × 2) AC Power Cord Carrying Bag CD-ROM Setup Guide "Read this first" Sheet Warranty Wireless adapter (Provided with models equipped with USB ports only. ) Mini D-Sub Cable General Guide CLASS 1 LASER PRODUCT Control panel Indicators Intake vents [P] (Power) key Brightness sensor Exhaust vents Projection lens Airflow vents Remote control signal receiver Lens cover Zoom ring Focus ring E-10 Getting Ready Loading Remote Controller Batteries Important! Be sure to use alkaline batteries only. *Caution RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 1. Open the battery cover on the back of the remote controller. 2. Load two new batteries into the case, making sure that their positive (+) and negative (­) ends are facing correctly. 3. Close the battery cover on the back of the remote controller. Replacing Remote Controller Batteries Open the battery cover on the back of the remote controller, replace the old batteries with new ones, and then close the battery cover. Important! To avoid running down the batteries, store the remote control unit so its buttons are not pressed inadvertently. Setting Up the Projector Locate the projector on a desk, table, or stand that is firm and level. Make sure to allow sufficient space around the sides and back of the projector for proper ventilation. The following illustrations show how the projector should be oriented for optimum projection relative to the screen. XJ-M140/XJ-M145/XJ-M150/XJ-M155 Screen QX-2328/XJ-M245/XJ-M250/XJ-M255 Screen Make sure the projector is at a right angle to the screen. Position the projector so the lens side is at the edge of the table, etc. The projector can be configured for projection from the back of a screen. For details, see the User's Guide on the CD-ROM that comes with the projector. E-11 Getting Ready Setup Precautions Use a conveniently located power outlet that you can reach easily when you need to unplug the projector. [. . . ] Plug the power cord back in and turn the projector back on again. If normal operation does not resume after you perform the above steps, take the projector to your retailer or authorized CASIO service center. E-19 Main Specifications Model Name Brightness (ANSI Lumens) Environment Power Approximate Dimensions Weight Specifications are subject to change without notice. XJ-M140/XJ-M145/ QX-2328/XJ-M245 2500 XJ-M150/XJ-M155/ XJ-M250/XJ-M255 3000 Operating Temperature: 5 to 35°C (41 to 95°F) Operating Humidity: 20 to 80% (non-condensation) Operating Altitude: 0 to 3, 000 meters (0 to 10, 000 feet) above sea level Requirements 100-240V AC, 50/60Hz, 2. 3A-1. 0A 311 (W) × 244 (D) × 84 (H) mm (12. 2" × 9. 6" × 3. 3") Approximately 3. 9kg (8. 6Ibs) E-20 GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U. S. A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ]