User manual CASIO SK-5 SERVICE MANUAL

[. . . ] Immediately turn power off and unplug the power cord from the wall outlet. Request servicing from your original dealer. AC adaptor · Do not allow the power cord to become damaged or broken, and never modify, over bend, twist, or pull it. Never place heavy objects on the power cord, and never expose it to direct heat. [. . . ] The formats that appear depend on the width of the tape loaded in the label printer and the number of lines in the block of text where the cursor is located when you press the SIZE key. The following shows all of the formats available for each tape width and the number of lines of text. · Note that with the preset formats, all character sizes have the same vertical and horizontal measurements. 24mm and 18mm tape, 1 line of text 1×1 4×4 2×2 5×5 3×3 To specify character sizes for lines of text using preset formats 1. While the cursor is located inside of the block of text where you want to use the preset formats, press SIZE. ­ ­ ­ ­ ­ S I ZE ­ ­ ­ ­ ­ S I ZE F OR M A T SUPER / SUB Tape width 1 × 1 (Manual Setting) Auto Fit 6 mm · See page E-16 for details about blocks. Use u and i to highlight "FORMAT" and then press SET. ­ ­ ­ ­ ­ S I ZE ­ ­ ­ ­ ­ ­ F OR M A T ­ 9 mm 12 mm 24mm and 18mm tape, 2 lines of text 1 × 1/1 × 1 2 × 2/1 × 1 1 × 1/3 × 3 1 × 1/2 × 2 2 × 2/2 × 2 3 × 3/1 × 1 · The FORMAT menu appears with all of the preset formats that are available in accordance with the number of text lines there are in the block where you located the cursor, and with the width of the tape loaded in the label printer. Use u, i, t and y to move the highlighting to the format that you want to use and then press SET to select it. · At this point, the label printer returns to the text input screen. 18 mm 24 mm 24mm and 18mm tape, 3 lines of text 1 × 1/1 × 1/1 × 1 1 × 1/2 × 2/1 × 1 12mm tape, 1 line of text 1×1 2×2 3×3 1 × 1/1 × 1/2 × 2 2 × 2/1 × 1/1 × 1 Important!Remember that changing the tape cartridge may make it impossible to print text if there are too many lines. Note the following relationships between tape width and the number of text lines. Tape Width 24 mm 18 mm 12 mm 9 mm 6 mm Plain Text 8 lines max. Print Area Frame Character Frame 6 lines max. Print Area The print area is the actual area of a label that contains printed text. It starts with the left side of the first character printed, and ends with right side of the last character printed. Side Spaces The side spaces are blank areas that the Label Printer automatically adds on either end of the print area. Note that side spaces are only added when you are using auto feed, and they are not added when using manual feed. To show the layout display 1. After laying out the label you plan to print, press LAYOUT. Feed setting (E-18) Screen number (when the entire layout does not fit on a single screen) 1L 19 . Use u and i to highlight "SUPERSCRIPT" or "SUBSCRIPT". · What you should do next depends on the range you want to use. · The range setting procedures are the same as those for font range settings. ALL: See "To change the font for all the text". BLOCK: See "To change the font for blocks of text". LINE: See "To change the font for lines of text". [. . . ] Re-input with the proper number of digits. Label printer was unable to receive data being sent from an external source. Check cable connections and parameter settings. Printing operation performed while the tape cartridge compartment is empty. [. . . ]