User manual CASIO WK-3000

[. . . ] E USER'S GUIDE WK3100-E-1 WK3100_e_cover. p65 1 04. 3. 26, 0:10 PM GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U. S. A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Pressing the START/STOP button to start playback from song memory always starts from the beginning of the song. · The entire keyboard functions as a melody keyboard, regardless of the MODE button setting. To turn off a specific track Press the SONG MEMORY TRACK button of the track you want to turn off, or use the Mixer (Page E-47) to turn off the channel of the track. E-64 WK3100_e_61-73. p65 64 04. 3. 26, 0:11 PM 735A-E-066A Song Memory Function To record chords with step recording 7 After you are finished recording, press the START/ STOP button. · This enters playback standby for the song you have just recorded. · To play back the song at this time, press the START/ STOP button. 1 Press the SONG MEMORY button three times to enter step recording standby, and then use the number buttons to select the song number (0 to 4). Flash NOTE S t e p Re c 2 3 Make the following settings. · Rhythm number · MODE button Press the CHORD/TR1 button, which is one of the SONG MEMORY TRACK buttons, to select Track1. · When recording starts, the REC indicator flashes on the display. After a few moments the indicator stops flashing, and remains on the display. · Use the procedure under "Correcting Mistakes While Step Recording" on page E-69 to correct input mistakes you make during step recording. · You can add on to a track that already contains recorded data by selecting that track in step 3 of the above procedure. Doing so automatically locates the step recording start point at the first beat immediately following the previously recorded data. · Inputting "0" as the chord length in steps 5 and 6 of the above procedure specifies a rest, but the rest is not reflected in the accompaniment contents when the accompaniment is played. 4 5 Press the SYNCHRO/FILL-IN NEXT button. Play a chord. · Use the chord play method that is specified by the current MODE button setting (Fingered, CASIO Chord, etc. ). · When the MODE button is set to Normal, specify the chord using the root input keyboard and chord type input keyboard. See "Specifying Chords in the Normal Mode" on page E-66 for details. Track 1 Contents After Step Recording In addition to chords, the following data is also recorded to Track 1 during step recording. This data is applied whenever Track 1 is played back. · Rhythm number · INTRO/ENDING 1 button, INTRO/ENDING 2 button, VARIATION/FILL-IN 1 button, VARIATION/FILL-IN 2 button, SYNCHRO/FILL-IN NEXT button operations Ch o r d Cord name Measure, beat, and clock at current location* NOTE · You can also use number buttons 1 through 7, and button 9 to specify the button release timing for the VARIATION/ FILL-IN 1, VARIATION/FILL-IN 2, and SYNCHRO/FILLIN buttons. For more information, see "Specifying the Length of a Note" on page E-66. Specifying release timing specifies that the applicable button remains depressed for a particular amount of time. If you do not specify the release timing, it is assumed that the button is pressed and then immediately released. * 96 clocks = 1 beat 6 Input the length of the chord (how long it should be played until the next chord is played). · Use the number buttons to specify the length of the chord. See "Specifying the Length of a Note" on page E-66 for details. · The specified chord and its length are stored in memory and the keyboard stands by for input of the next chord. · Repeat steps 5 and 6 to input more chords. 735A-E-067B E-65 65 04. 3. 26, 0:11 PM WK3100_e_61-73. p65 Song Memory Function Specifying Chords in the Normal Mode When the MODE button is set to Normal during step recording, you can specify chords using a method that is different from CASIO Chord and Fingered fingerings. This chord specification method can be used to input 18 different chord types using only two keyboard keys, so chords can be specified even if you don't know how to actually play them. Specifying the Length of a Note During step recording, the number buttons are used to specify the length of each note. Note lengths Use number buttons [1] through [6] to specify whole notes ( ), half notes ( ), quarter notes ( ), eighth notes ( ), 16th notes ( ), and 32nd notes ( ). Example: To specify a quarter note ( ), press [3]. Dots ( ) and triplicates ( ) While holding down the [7] (dot) or [9] (triplicate), use buttons [1] through [6] to input the lengths of the notes. Example: To input a dotted eighth notes ( ), hold down [7] and press [4]. [. . . ] I Parameters 0 : Tone (Range: 0 to 127) Adjusts the tone of the reverb sound. 1 : HPF (Range: 0 to 127) Adjusts the cutoff frequency of the high-pass filter. A larger value cuts the low range. Appendix 2 : Feedback (Range: 0 to 127) Adjusts the repeat of the reverb. A-23 A-24 M00 : Multi00 (Sin 2-Phase Chorus ­ 2-Tap Delay) 0 : Phaser Resonance 1 : Phaser Manual 2 : Phaser Rate 3 : Phaser Depth 4 : Chorus Rate 1 5 : Chorus Depth 1 6 : Chorus Rate 2 7 : Chorus Depth 2 I Function This is a multi effector that is related to Sin 2Phase Chorus - 2-Tap Delay. I Parameters 0 : Chorus LFO Rate 1 : Chorus LFO Depth 2 : Chorus Feedback 3 : Chorus Wet Level 4 : Delay Time 5 : Delay Wet Level 6 : Delay Feedback 7 : Delay High Damp I Parameters 0 : Flanger LFO Rate 1 : Flanger LFO Depth 2 : Flanger Feedback 3 : Flanger Wet Level 4 : Delay Time 5 : Delay Wet Level 6 : Delay Feedback 7 : Delay High Damp WK3000_e_A-19-31. p65 1 : Time (Range: 0 to 127) Adjusts the reverb time. I Parameters 2 : High Damp (Range: 0 to 127) Adjusts damping of the high-range reverb sound. The smaller the value, the greater the damping of high-range reverb sound. Appendix 3 : ER Level (Range: 0 to 127) Adjusts the level of the initial reflection. 24 4 : Wet Level (Range: 0 to 127) Adjusts the level of the effect sound. M03 : Multi03 (Flanger ­ 2-Tap Delay) I Function This is a multi effector that is related to Flanger - 2-Tap Delay. 28 : 2-Tap Delay I Function This is left/right 2-tap delay. I Parameters 0 : Delay Time (Range: 0 to 127) Adjusts the delay time. [. . . ]