User manual CASIO XJ-H1700

[. . . ] EFS DATA PROJECTOR XJ-H1600/XJ-H1650* XJ-ST145*/XJ-ST155* * USB port models * Modèles à port USB * Modelos con puerto USB English Setup Guide Be sure to keep all user documentation handy for future reference. Français Guide d'installation Conservez la documentation à portée de main pour toute référence future. Español Guía de configuración Asegúrese de tener a mano toda la documentación del usuario para futuras consultas. · Some models covered by this User's Guide may not be available in certain geographic areas. · Certains modèles couverts par ce mode d'emploi peuvent ne pas être commercialisés dans certaines zones géographiques. · Algunos modelos cubiertos por esta Guía del usuario pueden no estar disponibles en determinadas áreas geográficas. Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1 Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-7 About the Light Source Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . E-7 Laser Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-7 Other Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-8 Precaution when Handling the Projector after Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-9 Stowing the Projector in the Carrying Bag. . . . . E-9 Cleaning the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-9 Starting and Stopping Projection . . . . . . . . . . . . E-15 To start projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-15 To turn off the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Any operation or adjustment not specifically instructed by the user's guide creates the risk of hazardous laser radiation exposure. Bottom E-7 Operating Precautions Other Precautions This projector is made of precision components. Failure to observe the following precautions can result in inability to correctly save data and malfunction. Never use or store the projector in the following locations. Doing so creates the risk of malfunction of and damage to the projector. Locations subjected to electrostatic charge Locations subjected to temperature extremes Locations where there is extreme moisture Locations subjected to sudden temperature changes Locations where there is a lot of dust On a shaky, slanted, or otherwise unstable surface Locations where there is the danger of getting wet Avoid using the projector under the following conditions. Such conditions create the risk of malfunction of and damage to the projector. Avoid areas subject to temperature extremes (operating temperature range is 5°C to 35°C (41°F to 95°F)). Never place heavy objects on the projector or climb on top of the projector. Never insert or allow foreign objects to drop into the projector. Never place a vase or any other container of water on top of the projector. Whenever setting the projector down or performing any operation that involves moving or reorienting it, take care that you do not pinch your fingers under the projector. Never leave a dead battery inside the remote controller for a long time. A dead battery can leak, which leads to malfunction of and damage to the remote controller. Clean with a soft, dry cloth. When very dirty, use a soft cloth that has been dampened in a weak solution of water and a mild neutral detergent. Wring all excess water from the cloth before wiping. Never use thinner, benzine, or any other volatile agent to clean the projector. Doing so can remove its markings and cause staining of the case. Missing Screen Dots Though this projector is manufactured using the most advanced digital technology available today, some of the dots on the screen may be missing. This is normal, and does not indicate malfunction. Never subject the projector to strong impact while it is projecting. If the projector is accidentally subjected to strong impact, the projection image will momentarily go blank. The image will reappear after some time, but it may be the wrong color or it may be accompanied by an error message. If the projected image is the wrong color, re-select the current input source. If this does not return the projected image to its proper color, use the procedure under "To turn off the projector" on page E-15 to turn projector power off and then back on again. If the image reappears with an error message, correct the problem in accordance with the indicator explanations under "Error Indicators and Warning Messages" in the User's Guide on the CD-ROM that comes with the projector. E-8 Operating Precautions Keystone Correction and Image Quality Performing keystone correction causes the image to be compressed before it is projected. This can result distortion of the image or a loss of image quality. If this happens, change orientation of the projector and/or screen so it conforms as much as possible to the illustration under "Setting Up the Projector" on page E-12. If image quality is the highest priority, turn off auto keystone correction and position the projector so it is pointed straight at the screen. Even if your projector is still within the warranty period, you will be charged for repair if a problem is due to running the projector non-stop for very long periods (like 24 hours) or if the projector was set up and used without following the "Setup Precautions" on page E-13 of this manual. Precaution when Handling the Projector after Use The projector's front intake-exhaust vents and the area around the vents become very hot during operation, and will still be hot immediately after turning off the projector. Because of this, you should hold the sides of the projector as shown in the illustration whenever moving it. Stowing the Projector in the Carrying Bag Make sure the projector is no longer warm before stowing it in the carrying bag. Cleaning the Projector Periodically clean the projector exterior, lens, intake vents, and intake-exhaust vents on a regular basis. Dust and dirt tend to collect around the vents. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. [. . . ]