User manual CASIO XJ-SC215

[. . . ] English User's Guide (Basic Operations) · Be sure to read the "Safety Precautions" on page E-2 and "Operating Precautions" on page E-6 before trying to use this projector. · This manual covers only basic operations, including how to set up the projector, basic projector operations, and how to replace the lamp. For more detailed information, see the User's Guide (UsersGuide_English. pdf) on the CD-ROM that comes with the projector. Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-2 Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6 Lamp Handling Precautions . . . . . . . . . . . . . . . . . . . . . . E-6 Lamp Replacement Precautions . . . . . . . . . . . . . . . [. . . ] You can network up to four computers with a projector. Document Camera (YC-400/YC-430 Multi PJ Camera System) You can connect the YC-400/YC-430 Multi PJ Camera System directly to the USB port of the projector and project images of documents without going through a computer. For details about connecting these USB devices to the projector and procedures you need to perform to project images from a USB device, see "USB Function Guide" on the bundled CD-ROM. E-19 Getting Ready Turning On the Projector Before performing any of the operations in this section, make sure you first set up the projector and connect to an output device. AC Power Cord Precautions Use the AC power cord that comes with the projector. Make sure that you use a power source with the same voltage as that specified for the projector. Do not share the outlet supplying power to the projector with other devices. If you are using an extension cord, make sure that the ampere rating of the extension cord is compatible with the power consumption value of this projector. Never use the power cord while it is still bundled together. Never place objects on top of the power cord and do not step on it. Use a conveniently located power outlet that you can reach easily when you need to unplug the projector. If you need more information about the power supply, contact your original dealer or authorized CASIO service center. To turn on the projector 1. Use the bundled AC power cord to plug the projector into a power outlet. Plugging into a power outlet causes the three indicators on the top of the projector to light amber. After a short while, two of the indicators will go out and only the POWER/STANDBY indicator will remain lit amber, which indicates the standby state. Note that the projector will not turn on if you press the [ ] (power) key while all three indicators are lit amber. Wait until the projector is in the standby state before trying to turn it on. Power supply connector Bundled AC power cord The shape of the plug depends on your geographical area. This product is also designed for IT power distribution system with phase-to-phase voltage 230V. 2. 4. Turn on the computer or video device that is connected to the projector. If the projector's lens cover is closed, open it. Do not try to force the lens cover open past horizontal. Doing so creates the risk of malfunction. Press the [ ] (power) key. This causes the POWER/STANDBY indicator to flash green, which indicates that the projector is warming up. After warm up is complete, POWER/STANDBY indicator stops flashing and remains lit green, and the projector starts projecting an image from the device connected to it. A "Language" window will be projected the first time you turn on the projector. Use the procedure under "Specifying the Display Message Language" on the page E-21 to configure the language settings. E-20 Getting Ready If the Eco Mode is turned on, the LAMP indicator will light green when warm up starts. If the projector is hot when you plug the AC power cord into a power outlet, it will go into a cool down state. The cool down state is indicated by the POWER/STANDBY indicator flashing orange. Note that the projector will not turn on until cool down is complete, even if you press the [ ] (power) key. [. . . ] See page E-20 page E-34 -- page E-23 page E-17 User's Guide (UsersGuide_ English. pdf) E-38 Troubleshooting Problem The message "Input the password. " appears and further operation is not possible. Cause and Recommended Action The "Option Settings 1 Power On Password" setting on the setup menu is turned on, so the projector is password protected. Input the correct password, and then press the [ENTER] key. The remote controller battery may be dead. [. . . ]