User manual CASIO XW-P1

[. . . ] E XW-P1 USER'S GUIDE Please keep all information for future reference. Safety Precautions Before trying to use the instrument, be sure to read the separate "Safety Precautions". XWP1-E-1B NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] After you finish configuring settings, save them as described below. · Press WRITE to display the screen for saving a phrase (page E-48). · For information about deleting data you saved, see page E-71. 7 Saving a Phrase to an External Device · Memory card (page E-73) · Computer (page E-79) 1. Hold down bn KEY PLAY until the phrase selection screen appears on the display. Recording Over Another Phrase (Overdubbing) 1. Select the phrase you want to overdub. · To select a phrase, perform the same operation steps 3 through 6 for selecting a tone (page E-20). 2. Select the number of the phrase whose settings you want to configure. · To select a phrase number, perform the same operation steps 3 through 6 for selecting a tone (page E-20). 2. Press 7 EDIT. This will cause REC to flash. · If NEW is displayed as the "Rec Mode" setting, use the minus (­) and plus (+) buttons to change it to OVDB (overdubbing). This will enter the overdubbing standby mode. A phrase number and name will be shown on the display, but you cannot select a phrase at this time. bn bq 4. Use the bq up (q) and down (w) buttons to select a parameter and then use or the minus (­) and plus (+) buttons to change its setting. Menu Description bp bq · If you want, configure the note quantize (Note Qntz) setting (page E-46) at this time. Setting Range OriginalKey Original Key. Specifies the keyboard key that corresponds to the first note of the phrase played by Key Play. (The initial Original Key default C­ to G9 settings the note played when the phrase was recorded. ) · Setting can be specified using the keyboard keys. Specifies the key shift, in semitone steps, of a phrase when the keyboard key corresponding to the original is or the PLAY/ STOP key is pressed. (To disable key shift, specify 000. ) 3. Press bn REC or start playing with a pedal, knob, or wheel operation, or by playing something on the keyboard. Any one of these operations will start overdub recording. This will cause REC and PLAY/STOP to light (without flashing). · The original phrase will playback as a loop. Anything you play on the keyboard and any operations you perform during loop playback will be overdubbed onto the original phrase. bn bn 4. When recording reaches the point where you want to stop, press bn REC and bn PLAY/STOP will become unlit and an exclamation point (!) will appear next to the phrase number. ­127 to 000 to +127 bn PLAY/STOP. Key Shift E-47 Recording and Playing Back Phrases To pause overdubbing during looped playback In step 4 of the above procedure, press REC instead of PLAY/STOP. · This will cause REC to start flashing. · Though what has been recorded up to that point continues to play as a loop, further recording is not possible while overdubbing is paused. [. . . ] 5 :Noise2 Density (0, 1, 2, 3, 4, 5) Adjusts the frequency of Noise Generator 2. A larger number produces greater distortion. Raising the noise level while a note is not sounding will cause noise to sound, even if there is no input signal. 3. Find the same type names in the table under "Normal DSP Single Type DSP Parameters" on pages E-88 through E-90, and note the operation and setting ranges of the items that are the same as those shown in the "Configurable Parameters" column of the above table. [. . . ]