User manual CASTOR C6800

[. . . ] Any repairs or adjustment which might be necessary is to be carried out with the utmost care and attention. For this reason we reccomend you always contact the dealer where the appliance was sold ort our nearest Customer Service Centre, specifying the type of problem and the model of your appliance. Do not forget that the original spare parts are only to be found at our Customer Service Centres. GB Cet appareillage, avant de laisser l'usine, a été vérifié et mis au point par du personnel expert et spécialisé, de façon à donner les meilleurs résultats de fonctionnement. Toute réparation ou mise au point qui sera nécessaire par la suite devra être faite avec un maximum de soin et d'attention. [. . . ] To stop the bell, turn the knob leftwards without exerting a pressure, until the port or the hand coincides with symbol ELECTROMECHANICAL PROGRAMMER It is used to programme the oven start and stop. The programmer is fitted with an electric timer for displaying the hour. displays the programmer controls: use knobs A, B, and adjusting ring C, to carry out the necessary adjustments, such as: Knob A: Turn this knob clockwise to correct the time of the timer. (This is done when installing the appliance, when the current is cut out, for controlling both advance and lag, and so on). Knob B: Press and turn this knob clockwise to preset the cooking start time on dial F. Adjusting ring C: Turn this ring clockwise to preset the following: · cooking time (210 minutes max) · manual operation of the oven (position ) · acoustic signal cut off (position ) These signals appear on dial E 21 INSTRUCTIONS FOR USE GB Manual operation Programming the oven may not be necessary. In this case however, turn programmer adjusting ring C clockwise until symbol coincides with dial E. When adjusting the timer, check to make sure that the hour set on the timer is synchronized with the hour set on dial F. (A) (B) (C) A U T O General operation Working programme Automatic Setting the Timer When the oven is installed and the power supply is switched on, the display flashes and shows 0. 00. To set the time of day Press keys (1) and (2) at the same, and set the actual time, by pressing keys (-) and (+) within 4 seconds. The oven remains in manual operation and can be used without any programming. Important Information · Between 22. 00 hrs and 6. 00 hrs the display intensity is automatically dimmed. · If the acoustic signal is not disconnected (as per subsequent instructions), it cuts off after 2 minutes. 23 INSTRUCTIONS FOR USE GB · Any programming described below is active ted after approximately 4 seconds from the presetting. Press key (4) for the manual operation ("AUTO" pilot light off). ELECTRONIC END OF COOKING Setting up the hour Once the electronic connection is over, the display blinks and shows 0. 00. Press both keys at the same time and set out the hour by pressing keys (-) and (+) within the 4 seconds. The oven remains in manual operation and can be used without any further programmation. General remarks · If the horn is not deactivated (as per following instructions), it is cut off after 2 minutes. · All the programmings described hereunder are activated approx. · The maximum programming time is 23 hours, 59 minutes. · When the voltage is cut out, all the programmed set outs are erased. When the voltage returns, the display blinks and shows 0. 00. To reset the equipment, set out the hour and the programme again. Setting out the end of cooking To start the cooking at once, and to automatically set out the time, work as follows: · Select the funcion and the temperature required by the function selector and the thermostat. · Set out the cooking time using keys (-) and (+). [. . . ] Lift the hinge jumpers by your thumb and index fingers, then turn them fully outwards to the end of stroke (Fig. A). Turn the door towards the closure position and lay it on the jumpers: in this way the hinge's spring results as blocked. By fully closing the door the hinges are unhooked from the connection slits which are integral with the oven's muffle (sequence 1, 2, 3 of fig. B). 29 CLEANING AND MAINTENANCE GB Hooking the doors 1. Insert the door by hooking the hinges to the connection slits set on the muffle front. [. . . ]