User manual CAT EYE CC-2000

[. . . ] · When you want to start the odometer from zero, push the START/STOP button. L cm You can refer to the guide chart to roughly know the tire circumference. Tire size 14 x 1. 50 14 x 1. 75 16 x 1. 50 16 x 1. 75 18 x 1. 50 18 x 1. 75 20 x 1. 75 20 x 1-3/8 22 x 1-3/8 22 x 1-1/2 24 x 1 24 x 3/4Tubular 24 x 1-1/8 24 x 1-1/4 24 x 1. 75 24 x 2. 00 24 x 2. 125 26 x 7/8 26 x 1(59) 26 x 1(65) 26 x 1. 25 26 x 1-1/8 26 x 1-3/8 26 x 1-1/2 26 x 1. 40 26 x 1. 50 26 x 1. 75 26 x 1. 95 26 x 2. 00 26 x 2. 10 26 x 2. 125 26 x 2. 35 26 x 3. 00 27 x 1 27 x 1-1/8 27 x 1-1/4 27 x 1-3/8 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 40C 7 Starting the odometer from zero. Retaining the current odometer reading (the odometer starts from the reading you inputted) L(cm) 102 106 119 120 134 135 152 162 177 179 175 178 179 191 189 192 196 192 191 195 195 190 207 210 200 201 202 205 206 207 207 208 217 215 216 216 217 209 212 211 207 208 209 210 211 214 217 216 213 217 218 220 Important Note Front Fork Marked Line MODE ST/STOP Mount the sensor 3 at the appropriate position so that the center of the magnet 5 will align with the marked line on the sensor when the wheel is rotated. Important Note For two seconds. 3 5 3 Input the current reading of odometer. Increase the number. MODE Rotate the sensor on the front fork to adjust the gap between the sensor and the magnet 5 within 5 mm, and secure it with the nylon ties. 5 Within 5 mm Center ST/STOP Move the decimal point. 3 Mount The Bracket Secure the cord on the fork with the nylon ties 7 and lead to the handle bar along the outer cable of the bicycle by means of the spiral tube 8. Put the rubber pad 6 on the bracket 1 and secure the bracket on the handle bar with the screw. Slide the computer into the bracket 1 until you hear the click sound. The contact points are automatically closed. [. . . ] 300 cm 1 8 1 Lever 6 7 1 MODE SET Rotate the front wheel. Decrease the number Min. 100 cm ST/STOP 4 Test The Basic Functions Rotate the front wheel gently and see if the computer indicates the running speed. Note When the computer does not indicate the speed, check the position of the magnet and the sensor. OK Preparation Complete. (the screen will show the time measurement in this state) * The auto mode is ON in this state. Tire size is usually shown on the sidewall of tires. Computer Operations Selection of the data-display mode (bottom of the screen). Pressing the MODE button changes the functions in the sub-display. Clock Time - In Elapsed Time, press and hold the Mode button for two seconds to display Clock Time. Pressing the Mode button again will return the sub-display to Elapsed Time. Trip Distance 1 and 2 ­ The computer has two separate trip distances. It can be used to record distance within a ride or multiple days distances. In Trip Distance 1, press and hold the Mode button to select Distance 2. You will continue to view this distance until you select Distance 1 with the same procedure. The computer can be programmed to run in either MANUAL MODE or AUTO TIME MODE. The computer program for circumference is programmed for low speed use. We recommend to use this for MTB's. Elapsed Average Maximum · Moving Elapsed Time, Average Speed and Maximum Time Speed Speed Speed to the upper display. Minute Mx Upper Av Part Second You can move the Elapsed Time, Average and Max Speed Lower displays to the upper display for easier viewing. Hold the Hour SPD SPD Part START/STOP button for 2 sec. and the sub-display will appear in the upper display. Hold the START/STOP button again for 2 sec. and the display returns to the normal set up. ST/STOP Return to Clock display SET Increase the number MODE Clock 0:00 - 23:59 [1:00 - 12:59] SET ST/STOP When the measurements Set the hour are stopped. Set the minute Specifications Battery Life : --------------------------------- A Lithium Battery (CR2032), Approx:3 yrs (approx:1 hrs per day usage) Control System : ---------------------------- 4-bit 1-chip micro-computer (with a crystal oscillator) Display : -------------------------------------- Liquid crystal display Sensing System : --------------------------- No-contact magnetic sensor Range of Tire Circumference : ------------- 100 cm ­ 300 cm (Initial value ­ A:210 cm B:205 cm) Range of Operational Temperature : ------ 0°C ­ 40°C [32°F ­ 104°F] Dimension and Weight(Computer) : ------ 38 x 54 x 17. 5 mm [1-1/2 x 2-1/8 x 11/16"] / 28 g [1. 0 oz] * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice. Standard Parts Troubleshooting No display appears. Replace it by the new one and do all clear procedure. Strange data appears Do all clear procedure (write down the number of Odometer if possible before doing the all clear procedure and input it manually after choosing the measurement unit). [. . . ] In the case that this short-circuiting is detected by the computer, the computer is considered normal and the bracket and sensor may possibly have the cause of trouble. ) Is the gap between the sensor and the magnet too big?(should be within 5 mm) Does the marked line of the sensor align with the center of the magnet?Adjust the position of the magnet and the sensor. Make sure that the contact points of the bracket or of the main body are free from dirt. [. . . ]