User manual CAT EYE CC-5000 SOLAR 2

[. . . ] Note Allow enough wire clearance in the area marked with to insure you can turn the handlebars all the way from side to side without pulling the wire. Please read these instructions carefully before installing or using the CAT EYE ASTRALE 8. Installation of the Computer on Your Bike The computer comes with the following parts: 1 3 2 1 4 9 8 7 1 Bracket 2 Cord 3 Speed Sensor (Long Cord) 4 Cadence Sensor (Short Cord) 5 6 7 8 9 Sensor Rubber Pad Wheel Magnet Cadence Magnet Bracket Rubber Pad Nylon Ties (10) 3 6 Lever 8 9 Slide 1 5 2 4 1 Basic Functions Test Spin the rear wheel to see if Speed is reading properly. Push the mode button until Cadence (Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading properly. [. . . ] Note When the computer does not indicate the speed/cadence, check the position of the magnet and the sensor. Rotate the rear wheel. 1 OK Rotate the crank arm OK Mount the wheel magnet and speed sensor · Mount the wheel magnet 6 on a spoke of the rear wheel so the surface of the magnet faces the sensor. · Mount the speed sensor 3 (long cord) on the left chainstay with nylon ties 9. Note The nylon ties can only be used once, please install with care. Computer Set-up (For first use or after replacing the battery) 6 Rear wheel spoke 9 ! Contact Point 9 You need to know your tire size or the roll out length of your tire in MM's. Sensor Side The smooth edge of the zip tie should be on the outside 3 Left chainstay Refer to the chart below for approximate tire lengths. Tire size SET Button START/STOP Button MODE Button AC Button L mm Important Note Mount the magnets 6 and the sensors 3 in the appropriate positions so that the center of each magnet 6 aligns with the marked sensor line when the rear wheel and crank arm are rotated. The magnet should be no more than 5mm from the sensor. L(mm) 935 1020 1055 1185 1195 1340 1350 1515 1615 1770 1785 1753 1785 1795 1905 1890 1925 1965 1920 1913 1952 1953 1970 2068 2100 2005 2010 2023 2050 2055 2068 2070 2083 2170 2155 2161 2161 2169 2090 2125 2105 2070 2080 2086 2096 2105 2136 2170 2155 2130 2168 2180 2200 12 x1. 75 14 x 1. 50 14 x 1. 75 16 x 1. 50 16 x 1. 75 18 x 1. 50 18 x 1. 75 20 x 1. 75 20 x 1-3/8 22 x 1-3/8 22 x 1-1/2 24 x 1 24 x 3/4 Tubular 24 x 1-1/8 24 x 1-1/4 24 x 1. 75 24 x 2. 00 24 x 2. 125 26 x 7/8 26 x 1(59) 26 x 1(65) 26 x 1. 25 26 x 1-1/8 26 x 1-3/8 26 x 1-1/2 26 x 1. 40 26 x 1. 50 26 x 1. 75 26 x 1. 95 26 x 2. 00 26 x 2. 10 26 x 2. 125 26 x 2. 35 26 x 3. 00 27 x 1 27 x 1-1/8 27 x 1-1/4 27 x 1-3/8 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 40C 3 Left chainstay Rear wheel spoke 6 Center Marked Line 3 Adjust Within 5 mm 1 2 All Clear Push the AC button on the backside. * Push the AC button when using this system for the first time and every time the battery is replaced. AC Button 6 Measurement Selection Select the measurement unit, kilometer or mile, by pushing the MODE button. Fix it by pushing the SET button. 2 Mount the cadence magnet and cadence sensor. · Mount the cadence magnet 7 on the left crank arm so that it faces the sensor. · Secure the cadence sensor 4 (short cord) on the left chain stay with nylon ties 9. 9 9 Sensor Side Kilometer MODE Mile SET 7 Inward Side of The Crank Arm Left Chain Stay 3 Important Note When the crank is spinning, the center of the magnet 7 should pass in front of the sensor 4 marking line. The distance between the sensor and the magnet 7 should be within 5mm. After adjusting the magnet and sensor, secure tightly with nylon ties. Left Chain Stay 3 Set The Tire Circumference Set the tire circumference in mm. Note Refer to the chart shown on the right. Setting is fixed and completed by pushing the SET button. Increase the number Max. Switch it back START/STOP with the same procedure. Speed Cadence While any measurement is displayed on the screen MODE Setting The Clock Time 24 hour or 12 hour system is to be used with km/h or mph unit respectively. Increase the number Return to Elapsed Time display SET Return to Clock display MODE Clock 0:00 - 23:59 [1:00 - 12:59] SET When the measurements are stopped. Set the hour START/STOP Set the minute Specifications Battery/Its Life : ----------------------------- A Lithium Battery (CR2032), Approx:3 yrs. (Approx:1 hr per day usage. ) Control System : ---------------------------- 4-bit 1-chip micro-computer (with a crystal oscillator) Display : -------------------------------------- Liquid crystal display Sensing System : --------------------------- No-contact magnetic sensor Range of tire circumference setting : ----- 10 mm - 2999 mm (Initial value 2096 mm) Range of Operational Temperature : ------ 0°C - 40°C (32°F - 104°F) Dimension and Weight(Computer) : ------ 38 x 54 x 17. 5 mm [1-1/2 x 2-1/8 x 11/16"] / 28 g [1. 0 oz] * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice. Standard Parts Troubleshooting No display appears. Strange data appears Do all clear procedure. Measurements do not start when the START/STOP button is pushed. Turn the Auto-Mode off to enable the start or stop of the measurements by manual operation of the button. No speed or cadence data can be measured. The contacts to be short-cir(If the speed or cadence data is not displayed, have the contact cuited intermittently are located points short-circuited a few times by a metal plate. that this short-circuiting is detected by the computer, the computer is considered normal and the bracket and the sensor possibly have the cause of trouble. ) Is the gap between the sensor and the magnet too big? [. . . ] (should be within 5 mm) Speed Cadence Does the marked line of the sensor align with the center of the magnet?Adjust the position of the magnet and the sensor. Wipe the contact points of the bracket or computer clean. Even if the outside of the cord looks normal, there could be damage. [. . . ]