User manual CAT EYE CC-8000 ATC

[. . . ] Wheel circumference varies with the tire pressure. * Les valeurs indiquées sont approximatives. La circonférence de roue varie en fonction de la pression de gonflage du pneu. * Die angegebenen Zahlen sind nur Näherungswerte. Der Radumfang kann je nach Reifendruck verschieden sein. [. . . ] Has the battery in the main unit worn out?Incorrect data appears or the screen is frozen. (If possible, write down the Odo data before all clear operation, and input it again after the display returns normal. ) Current speed does not appear. (When current speed does not appear, first short-circuit the contact on the back with metal; if the speed display appears, the main unit is normal and the problem must be in the bracket or the sensor. ) Is there anything on the contact of the main unit or of the bracket?Is the distance between the sensor and the magnet too far?Are the marking line of the sensor and the center of magnet aligned?Adjust the position of the sensor and magnet again. Close Continuously measured until battery wears down. Displayed with 0. 1 resolution up to 9999. 9 km and with 1. 0 resolution up to 99999 km. (With all clear operation, it returns to zero; to continue accumulation of data, input the previous Odo data after all clear operation. ) Dst(1, 2) Trip Distance(1, 2) 0. 00 - 999. 99 mile[km] ±0. 01 mile[km] Dst1 Dst2 The trip distance from start to current point is displayed. Two different start points can be set (Dst1 and Dst2). Spin the front wheel and check if the speed display appears. (If not, adjust the relative positions of magnet and sensor again. ) Fasten the sensor securely, and remove the main unit. 6 2 Attach the sensor temporarily. Note: Sensor Band-A (Small) --------- 11Ø-26Ø (Large) --------- 21Ø-36Ø 5 9 9 5 Secure the wire along the fork with the nylon ties 9, and wind it round the brake cable(3) up to the handlebar. Note: Allow enough wire length in the area marked with in the illustration, to insure full movement and unhindered operation of the handlebar. 3 7 4 1 (3) 1 3 3 6 (1) (2) 9 8 Test the alignment of the magnet and sensor with the main unit attached. Align the magnet's center(1) and the sensor's marking line(2). 2mm clearance between the magnet 6 and sensor 3. 3 6 (2) (1) How to Attach Main Unit to Bracket (4) 2mm Slide main unit onto the bracket from front until it clicks into position. To remove, pull it off forward while pushing down the lever(4). 1 ORIGINAL SET UP FOR THE MITY 3 AND ENDURO 2 ALL CLEAR OPERATION ST. /STOP button (S) MODE button SET button decrease the digits L cm SET UP FOR RIDING on back K (km/h)= 24hr. clock The complete screen will light up for a moment and then all fade away. The only thing on the screen will be a flashing "K". Select the speed scale you would like by pressing the MODE Button. "K" for kilometers and "M" for miles per hour. Note that the speed scale you select DICTATES CLOCK function in 12 or 24 hours. [. . . ] In M (Mile per hour) a 12 HOUR CLOCK is selected. WHEEL SETTING A or B The computer has two wheel settings for quickly and conveniently moving the between two bikes with different size of tires. You can tell which WHEEL SETTING you are in by the semicircle symbol with an "A" or "B" on the computer screen. Wheel setting "A" has been preset with a tire size for a 700 X 23C road tire. Wheel setting "B" is preset for a mountain bike tire of 26 x 1. 95. [. . . ]