User manual CAT EYE CC-CL100 (CORDLESS)

[. . . ] To return the product, pack it carefully and remember to enclose the warranty certificate with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to our service shall be borne by person desiring service. Address for service: CO. , LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn. : CAT EYE Customer Service Section Service & Research Address for United States Consumers: CATEYE Service & Research Center 1705 14th St. [. . . ] At 100, 000 miles(km), it returns to zero and counting begins anew. M M Maximum Speed 0. 0(3. 0) to 65. 9mile/h ±0. 3 mile/h With Reset operation, it returns to zero and counting begins anew. BUTTON FUNCTIONS CATEYE ASTRALE CC-CD100 ·Mode Button (left button) The display mode mark shift in the illustrated sequence each time the button is pressed, and the corresponding data is simultaneously displayed on the sub-display. If the mode button is held for over 2 seconds, 24-hour clock will be displayed. A A Average Speed 0. 0 to 65. 9 mile/h ±0. 3 mile/h Current Speed on Main Display T C CATEYE ASTRALE The average speed from start to current point is displayed within 27 hours 46 minutes 39 seconds (99. 999 seconds) or 999. 99 miles (km). If either is exceeded, (. E) is displayed and calculation ceases. ·Start/Stop Button (right button) CC-CD100 O M A D Measuring of the Trip Distance and Elapsed Time is simultaneously started or stopped when the Start/Stop button is pressed. During operation the speed scale symbol flickers. Pressing the mode button can shift the main display from Current Speed to Cadence when Auto Mode is functioning. A D D Trip Distance 0. 00 to 999. 99 mile ±0. 01 mile The trip distance from start to current point is displayed. With Reset operation, it returns to zero. CATEYE ASTRALE CC-CD100 ·Set Button (middle button) When the Set Button is pressed in the stop state in each mode, the following value can be changed; · In (O) mode . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel Circumference · In 24-hour Clock mode . . . . . . . . . 24-hour Clock · In (T), (D), (A) mode . . . . . . . . . . . . . . . on/off the Automatic Start/Stop T T Elapsed Time 0:00'00" to 9:59'59" ±0. 003% Cadence on Main Display Elapsed time is measured from start to current point, in units of hours, minutes and seconds. At 10 hours, it returns to zero and counting begins anew. With Reset operation, it returns to zero. CATEYE ASTRALE CC-CD100 T S O M A D ·RESET: Select any mode except Total Distance (O), and press the Mode button and Start/Stop button simultaneously. Is there anything on the contact of the main unit or of the bracket?Is the distance between sensor and magnet too far?Are the marking line of the sensor and the center of magnet matched each other?Refer to "Sensor/Magnet Mounting" and re-adjust correctly. Replace the Bracket & Sensor part with a new one. Transmission signal loss in damp or wet conditions. Water or condensation may collect between the bracket sensor and the computer causing an interruption in the data transmission. Contacts can also be treated with a water repellent silicon jell from an automotive parts or hardware store. Do not use industrial water repellent; it may damage the bracket. When the START/STOP Button is pressed, the unit doesn't activate or stop. The START/STOP Button doesn't function in the Auto function. L Fig. 4 3. [. . . ] When replacing, be careful not to press the buttons. Replacement must be done promptly (within 20 seconds). After replacement, don´t press AC button, because the data including total distance (odometer) is continuously measured. However, the following malfunction might occur after replacement: ·No display appears. [. . . ]