User manual CAT EYE CC-CL200

[. . . ] To set the 24-hour clock time: Stop the measurement in ( ) mode, then press the SET button. To set auto mode to ON or OFF: Select the (T), (A) or (D) mode, then press the SET button. 24 x 1 24 x 3/4 Tubular 24 x 1-1/8 Tubular 24 x 1-1/4 24 x 1. 75 24 x 2. 00 24 x 2. 125 26 x 1(559mm) 26 x 1(650c) 26 x 1. 25 26 x 1-1/8 Tubular 26 x 1-3/8 26 x 1-1/2 26 x 1. 40 26 x 1. 50 26 x 1. 75 26 x 1. 95 26 x 2. 00 26 x 2. 1 26 x 2. 125 1753 1785 1795 1905 1890 1925 1965 1913 1952 1953 1970 2068 2100 2005 1985 2030 2050 2055 2068 2070 26 x 2. 35 27 x 1 27 x 1-1/8 27 x 1-1/4 27 x 1-3/8 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 44C 2083 2145 2155 2161 2169 2090 2125 2105 2070 2090 2086 2096 2105 2136 2170 2155 2130 2168 2180 2224 Fig. 4 · A ·AC (All Clear) Button (bottom right button) When this button is pressed, all the data stored in memory is cleared. After all displays illuminate, the "mile/h" symbol illuminates. This button should be pressed only after replacing the battery or when irregular display of information occurs due to static electricity, etc. [. . . ] (Refer to the explanation of Auto Mode function. ) While keeping the right button pressed , press the SET button. The first wheel circumference measurement will be displayed for a few seconds, then the second setting will appear. #169-6690 Parts Kit #169-6660 Bracket Kit sensor band B sensor rubber pad sensor band A Fig. 12 sensor band B sensor rubber pad 5. How to reset the Wheel Circumference Select the (O) mode and stop the measurement. Press SET button and the already set wheel circumference will blink on the sub-display. Refer to '3. Setting the wheel circumference' to complete the setting. Setting the 24-hour Clock (Fig. 8) Press left button for more than 2 seconds to select the 24-hour clock display. Stop the measurement by pressing the right button. Press SET button and the minute display will start to blink. Press right button to select a minute time sensor band A ahead of the current time by 1 to 2 minutes. Next press left button and the hour parallel will blink. Press right button to set to current hour time. Press SET button to complete the setting. Fig. 13 #169-6670 Cordless Sensor #169-6680 Universal Sensor Band screw sensor Fig. 14 spacer front fork MOUNTING TO BIKE If necessary, use either the 1mm or 2mm thick rubber pads according to the handlebar diameter. · Slide the main unit onto the bracket from front until it clicks into position. To remove the main unit, pull it forward while depressing the lever on bracket (fig. 10). How to Mount the Sensor on the Right Front Fork Leg. (fig. 11) #169-6667 Center Mount Bracket Kit #169-6669 Stem Mount Bracket Kit Mount the sensor in the highest possible position on the right front fork leg. Adjust the position, clearance and direction as follows: (1) Insert the band B into the slit of the band A, and put the rubber pad inside of the band A (fig. Adjust the length of the bands in order that the screw-fastening part of the bands is parallel when mounted to the fork (fig. * To pull out the band B from band A, tug strongly. long screw (2) Mount the adjusted bands to fork along with the sensor, by temporarily Fig. 15 tightening the screw (fig. 14). If the space between front fork and spoke of your bike is big, use the spacer and long screw as in the fig. 15, so that the clearance between sensor and magnet will be approx. (3) Use a coin to install the magnet securely to the spoke so that it face the sensor zone. (fig. 16 & 17) magnet (4) A 5mm clearance shall be kept between the sensor and magnet(fig. 18). triangle mark Then align the magnet with sensor zone (fig. 16). Meanwhile, the sensor shall aim at the main unit indicated by the triangle marked on the sensor. [. . . ] --------------------------- Check the sensor position and direction. Speed is not displayed when riding with high speed or at low temperature. --------------------------------------------------------------------- Check the sensor position and direction. --------------------------------------------------------------------- Has the battery worn out? [. . . ]