User manual CAT EYE CC-FR7CL (CORDLESS 7)

[. . . ] CCMFR7CL-021210 Printed in Japan 066600165 1 About cordless system The sensor picks up the wheel revolution signal and transmits the signal to the computer; the computer calculates and displays the data on the screen. CAUTION: In order to prevent external signal interference, the signal reception range is limited. For best performance, the distance between the sensor and the computer must be kept within 70cm. Attach the sensor at the upper part of your fork so that the distance becomes less than 70cm. [. . . ] · START/STOP button moves to the next digit. · Press the SET button when complete. SET MODE increase the figure MODE move to the next digit Sensor Base (fig. C) 2 Sensor Base ST. /STOP NOTE: When the wheel rotates, the magnet MUST line up with the mark on the sensor. ALSO NOTE: Magnet must pass within 5 mm of the sensor--if not, it will not trip the sensor as it passes, and the computer will not register speed. Adjusting the sensor position higher or lower on the fork leg or by rotating the sensor on the fork mount may be required to achieve proper distance to the wheel magnet. Less than 5mm SET 3 2 Magnet's center Marking line 3 2 Spin · · · · · · Wheel circumference number is shown. Look at chart to find TIRE SIZE in "mm". To increase TIRE SIZE press MODE button. Press SET button when finished. increase the figure MODE 3 4 Test by spinning the front wheel. If not, make sure 1) the magnet is close enough to sensor (within 5 mm); and 2) the sensor is close enough to computer head (within 70 cm) and 3) nothing is obstructing the line of sight between the sensor and the computer head. decrease the figure ST. /STOP OK Sensor Pulse Indicator SET Setup Completed (To Tm) In this state Auto Time is ON. Operation of Computer Speed Scale Indicator - "mph" or "km/h" on main display flashes when computer is measuring speed. Display Modes - Press MODE button to shift lower display from one mode to the next. The display modes change from Elapsed Time (Tm), to Average Speed (Av), to Maximum Speed (Mx), to Total Odometer (Odo), to Trip Distance (Dst). CLOCK TIME - Hold MODE button for 2 seconds to display Clock Time (this works in any of the display modes). [To set correct Clock Time, press SET button when Clock Time is showing in lower display. Use MODE button to increase the digit number, and press SET to change to next digit. - When this is activated, the computer will autoAUTO TIME matically start and stop measuring Elapsed Time (Tm), Average Speed (Av), and Trip Distance (Dst), as soon as the bike starts icon shows in main moving. To turn feature on or off, press SET button while lower display is in Elapsed Time (Tm), Average Speed (Av), or Trip Distance (Dst) activated. For best results, operate the computer with MANUAL MODE - Press the START/STOP button to start the Elapsed Time (Tm), Average Speed (Av) and Trip Distance (Dst) is not activated. measurement, ONLY IF AUTO TIME Reset Time, Distance, Average - To reset (zero out) ride data (Elapsed Time, Trip Distance, Average Speed, and Max. Speed), press MODE and START/STOP simultaneously. [Total Odometer is not reset]. Speed Scale Indicator Display Features Speed (upper display) 0. 0(4. 0)-105. 9 km/h [0. 0(3. 0)-65. 9 mph] No signal 10 minuets Power Saving Function (When the unit doesn't receive signal for ten minutes, it enters into power saving mode. ) Sensor Pulse Indicator Flashes in synchronization with signal from sensor. Wheel Icon Shows which wheel is selected Auto Time Icon Starts/stops measuring automatically. 2 weeks later Power Saving Mode When wheel starts rotating, it returns to normal mode. Sleep Mode To wake up the unit, press MODE button or ST. /STOP button. How Mode Shifts in Lower Display Pressing MODE and ST. /STOP button simultaneously for a few seconds in Mx mode, the computer will go to sleep mode. Tm Elapsed Time 0:00'00"-9:59'59" Dual Tire Size You can set 2 different wheel circumferences How to Switch Wheel and Av Average Speed Tm Av SET Dst Press SET button in Tm, Av or Dst 0. 0-105. 9 km/h [0. 0-65. 9 mph] If Elapsed Time exceeds 27 hours or Trip Distance exceeds 999. 99km, Average Speed shows E. and ceases calculation. In any functions other than Odo SET Hold down 2 seconds In Odo Road Racer MTB MODE ST. /STOP Mx Maximum Speed Start/Stop MODE 0. 0(4. 0)-105. 9 km/h [0. 0(3. 0)-65. 9 mph] Press simultaneously 2 seconds How to Change Wheel Circumference Odo MODE ST. /STOP Total Distance 0. 0-99999 km [mile] SET Road Racer Default figure Wheel A: 2096 Wheel B: 2050 Increases figure MODE MODE ST. /STOP Computer Features Power Saving Function: · Power saving mode ------- No signal for 10 minutes. [. . . ] Is the distance between the computer and the sensor too long?Adjust the sensor's position so that the distance becomes less than 70cm. *In winter, battery's performance is degraded. Replace it with a new one and do all clear operation. Specification Battery ------------------------------ Computer: Lithium Battery CR2032 X 1 Sensor: Lithium Battery CR2032 X 1 Battery Life ------------------------- Computer: approx. [. . . ]