User manual CAT EYE MSC 3DX

[. . . ] Caution: Attach the sensor and the magnet within 10cm from the hub axle. Spoke @ Attach the speed sensor 2 temporarily to the right front fork. Adjust the sensor 2 and the magnet q referring to the conditions A and B . After adjusting, tighten the screw 0 and the magnet q. Front fork # Attach the cadence sensor 3 temporarily to the left chain stay. $ Attach the cadence magnet w to the crank. Adjust the position of the sensor and the magnet referring to the conditions A and B . [. . . ] Never press the main unit forcibly onto the bracket. Caution: When riding, do not touch the lever; the main unit might fall off. Remove: To remove the main unit, unwind the wristband and push the lever. -4PUSH Hook How to mount the unit to bicycle Release Lever Remove Release Lever Input the wheel circumference of your bicycle into the main unit. Find out your bicycle's wheel circumference from the table below. If you cannot fine one, use the default figure " 2096" temporarily. Name of Button The tire size is marked on the side of your tire. Wheel Circumference = L 3 Setting up Main Unit wheel circumference !-1 (1) Initial Setting Select a Speed Scale The main unit has 6 buttons: SET/AT button, MODE button, LAP button, LT button, S/S button and AC button. -1) Follow the instruction below for the initial setting. Then the entire screen illuminates and gives a beep sound. Push the MODE button to switch between "km/h" and "mph". Push SET/AT button to choose the desired speed scale. Then appears and the initial figure 2096 flashes. -3) !-2 Setting the Wheel Circumference 3. Input your bicycle's wheel circumference obtained from the above table. Push MODE button to increase the digits, and LAP button to decrease. (To increase/decrease rapidly, hold down the respective button. ) Caution: This is just the temporary setting of the wheel circumference. For more accurate measurement, input the exact wheel circumference. When you want to change wheel circumference later, refer to "Changing wheel circumference" in page 13 of the user manual. Push SET/AT button to fix the setting, and the screen shows "Current Speed " in the upper display, "Heart Rate " in the middle display and "Elapsed Time TM" in the lower display (!Initial setting is completed. !-4 !-3 "Elapsed Time TM" Tire Size 24 x 1 24 x 3/4 Tubular 24 x 1-1/8 Tubular 24 x 1-1/4 24 x 1. 75 24 x 2. 00 24 x 2. 125 26 x 1 (559mm) 26 x 1 (650C) 26 x 1. 25 26 x 1-1/8 Tubular 26 x 1-3/8 26 x 1-1/2 26 x 1. 40 26 x 1. 50 26 x 1. 75 26 x 1. 95 26 x 2. 00 26 x 2. 10 26 x 2. 125 26 x 2. 35 27 x 1 27 x 1-1/8 27 x 1-1/4 27 x 1-3/8 650 x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 44C mm 1753 1785 1795 1905 1890 1925 1965 1913 1952 1953 1970 2068 2100 2005 1985 2023 2050 2055 2068 2070 2083 2145 2155 2161 2169 2090 2125 2105 2070 2090 2086 2096 2105 2136 2170 2155 2130 2168 2180 2224 -5- (2) Basic Operations Start and stop measurement Push S/S button and the unit will start measuring "Elapsed Time TM". At the same time, calculation of "Trip Distance DST" and "Average Speed AVS" starts. The symbol of bpm in the middle display flashes while measuring. Push S/S button again and the unit stops measuring and calculation. "Current Speed "Cadence Switching Functions ", "Heart Rate ", ", "Total Distance ODO", "Maximum Heart Rate MXP" and "Maximum Speed MXS" continue to be measured and displayed regardless of the start/stop. [. . . ] Caution: When this feature is on, you cannot start/stop the measurement by button operation. Therefore this feature is useful only when riding bicycle. When you use this unit on your wrist as a heart rate monitor, turn off the Auto time feature. Changing Upper Display In the Default State the upper display always shows "Current Speed ". However, you can change it to Clock or Cadence , by pressing SET/AT button and S/S button simultaneously. [. . . ]