User manual CATERPILLAR SH680 BROCHURE

[. . . ] Extra leg room, easy-to-reach long-life rocker switches and revolutionary joystick controls make this the most comfortable cab in the industry. Standard HVAC system The high capacity system dehumidifies and pressurizes the cab, circulates fresh air, seals out dust and keeps windows clear. Low Interior Sound and Vibration Levels Multiple isolation mounts along with relocated hydraulic pump and valves significantly improve operator comfort and productivity. In-Dash Instrument Cluster Easy-to-read, high-visibility gauges and warning lamps keep the operator aware of critical system information. 3 Steering and Implement Controls Unprecedented precision and ease of operation. Ease of Operation Two electro-hydraulic joysticks require up to 78% less hand and wrist movement than conventional lever controls for greatly enhanced operator comfort and efficiency. The intuitive control pattern allows both new and experienced operators to quickly become productive. Electronically adjustable control pods help position joysticks for optimal comfort, visibility and proper operation. Joystick Functions · The left joystick primarily controls the machine direction and speed including steering, articulation, return-to-center, wheel lean, gear selection, left moldboard lift cylinder and float. The right joystick primarily controls drawbar, circle and moldboard functions including right moldboard lift cylinder and float, moldboard slide and tip, circle turn, drawbar center shift, electronic throttle control and manual differential lock/unlock. · Intuitive Steering Control Joystick lean angle mirrors the steer tires' turning angle. [. . . ] Controlled Throttle Shifting helps to smooth directional and gear changes without using the inching pedal. Load Compensation ensures consistent shift quality regardless of blade or machine load. This standard feature automatically shifts the transmission at optimal points so the operator can focus on the work to help improve safety, productivity and ease of operation. Power Shift Countershaft Transmission and the Cat C9. 3 engine maximize power to the ground. Eight forward/six reverse gears optimize productivity. Engine Over-Speed Protection prevents downshifting until an acceptable safe travel speed has been established. · · · · · Bolt-On Modular Rear Axle Improves serviceability and contamination control with easy access to differential components. Hydraulic Brakes Hydraulically actuated, oil bathed, multi-disc service brakes at each tandem wheel (1) offer the industry's largest total brake surface area (2) for dependable stopping power and long brake life. The brake wear indicator/compensator system (3) maintains brake performance and indicates brake wear without disassembly, for fast servicing and longer brake service life. The spring-applied, hydraulically released multidisc parking brake, sealed and oil-cooled for long life and low service, is integrated into the Operator Presence System to prevent unintended machine movement. 6 Structures and DCM Service ease and precise blade control. Heavy Duty Durability The frame, drawbar and one-piece forged steel circle are designed for durability in heavy duty applications. The strong A-frame drawbar uses a durable tubular design. The front 240° of circle teeth are hardened to reduce wear and ensure component reliability. Articulation Hitch A large tapered roller bearing at the lower pivot carries loads evenly and smoothly. Sealed to prevent contamination, a locking pin prevents articulation for safety during service or transport. Aggressive Blade Angle Allows material to roll more freely along the blade, particularly dry materials or cohesive soils. Please consult your Cat dealer for availability. 10 Work Tools and Attachments Equip your machine for the job. Moldboard Options Standard 3. 7 m (12 ft) or optional 4. 3 m (14 ft). Left and right side extensions are also available. Ground Engaging Tools (GET) A variety of tools are available from Cat Work Tools, including cutting edges, graderbits and end bits, all designed for maximum service life and productivity. Front Mounted Groups A front mounted push plate/counterweight or front lift group are available. The front lift group can be combined with a front dozer blade or front scarifier for added versatility. Rear Ripper/Scarifier Made to penetrate tough material fast and rip thoroughly for easier movement with the moldboard. The ripper includes three shanks (with holders for five). Nine scarifier shanks can also be added for additional versatility. Snow Removal Work Tools Multiple snow plow, snow wing and mounting options increase machine versatility and utilization throughout the year. 11 Safety Protect your most valuable resource. Designed with Protection in Mind Features are designed to enhance operator and job site safety, such as drop-down rear lights and a rearview camera. Among many standard safety features are laminated glass, back-up lights, and perforated tandem walkways and grab rails. Operator Presence System The parking brake remains engaged and hydraulic implements disabled until the operator is initially seated and the machine is ready for operation. Secondary Steering System Automatically engages an electric hydraulic pump in case of a drop in steering pressure, allowing the operator to steer the machine to a stop. Hydraulic Lockout A simple switch located in the cab disables all implement functions while still providing machine steering control. This safety feature is especially useful while roading. Brake Systems Brakes are located at each tandem wheel to eliminate braking loads on the power train. Redundant brake systems utilize accumulators to enable stopping in case of machine failure, further increasing operational safety. Circle Drive Slip Clutch This standard feature protects the drawbar, circle and moldboard from shock loads when the blade encounters an immovable object. It also reduces the possibility of abrupt directional changes in poor traction conditions. Blade Lift Accumulators (Optional) This optional feature uses accumulators to help absorb impact loads to the moldboard by allowing vertical blade travel. Blade lift accumulators help reduce unnecessary wear and also help reduce impact loading for enhanced operator safety. Rearview Camera (Optional) Visibility is further enhanced with an optional Work Area Vision System (WAVS) through a 178 mm (7 in) LCD color monitor in the cab. Developed specifically for rugged applications, this durable camera improves productivity and increases operator awareness of surroundings. Front and Rear Fenders (Optional) To help reduce objects flying from the tires, as well as build-up of mud, snow and debris, optional fenders can be added. 12 Customer Support Unparalleled worldwide support. Renowned dealer service From helping you choose the right machine to financing and ongoing support, your Cat dealer provides the best in sales and service. [. . . ] Turning radius, outside front tires Steering range ­ left/right Articulation angle ­ left/right Fwd. 1st 2nd 3rd 4th 5th 6th 46. 6 km/h 29. 0 mph 36. 8 km/h 22. 9 mph 7. 6 m 24 ft 10 in 47. 5° 20° Power Train Forward/ Reverse Gears Transmission Brakes Service Service, surface area Parking Secondary 8 Fwd/6 Rev Direct Drive, Powershift Multiple Oil Disc 23 000 cm2 3, 565 in2 Multiple Oil Disc Dual Circuit 4. 1 km/h 5. 5 km/h 8. 0 km/h 11. 0 km/h 17. 1 km/h 23. 3 km/h 32. 0 km/h 46. 6 km/h 3. 2 km/h 6. 0 km/h 8. 7 km/h 13. 5 km/h 25. 3 km/h 36. 8 km/h 2. 5 mph 3. 4 mph 5. 0 mph 6. 9 mph 10. 6 mph 14. 5 mph 19. 9 mph 29. 0 mph 2. 0 mph 3. 7 mph 5. 4 mph 8. 4 mph 15. 7 mph 22. 9 mph Calculated with no slip and 14R24 tires. 14 Service Refill Fuel Capacity Cooling system Hydraulic system Total Tank Engine Oil Trans. /Diff. / Final Drives Tandem housing (each) Front wheel spindle bearing housing Circle drive housing 416 L 56 L 100 L 64 L 30 L 65 L 64 L 0. 5 L 7L 110 gal 14. 8 gal 26. 4 gal 16. 9 gal 7. 9 gal 17. 2 gal 16. 9 gal 0. 13 gal 1. 8 gal Tandems Height Width Sidewall thickness Inner Outer Drive chain pitch Wheel axle spacing Tandem oscillation Front up Front down 506 mm 210 mm 16 mm 18 mm 50. 8 mm 1522. 8 mm 15° 25° 19. 9 in 8. 3 in 0. 63 in 0. 71 in 2 in 59. 95 in Blade Range Circle centershift Right 728 mm 28. 7 in Left 695 mm 27. 4 in Moldboard sideshift Right 660 mm 26 in Left 510 mm 20. 1 in Maximum blade 90° position angle Blade tip range Forward 40° Backward 5° Maximum shoulder reach outside of tires Right 1978 mm 77. 87 in Left 1790 mm 70. 5 in Maximum lift 480 mm 18. 9 in above ground Maximum depth 715 mm 28. 1 in of cut Moldboard Blade width Moldboard Height Thickness Arc radius Throat clearance Cutting edge Width Thickness End Bit Width Thickness Blade Pull Base GVW Max GVW Blade Down Pressure Base GVW Max GVW 3. 7 m 610 mm 22 mm 413 mm 166 mm 152 mm 16 mm 152 mm 16 mm 11 687 kg 15 455 kg 7423 kg 13 243 kg 12 ft 24 in 0. 87 in 16. 3 in 6. 5 in 6 in 0. 6 in 6 in 0. 6 in 25, 765 lb 34, 072 lb 16, 365 lb 29, 196 lb Frame Circle Diameter 1530 mm Blade beam 40 mm thickness Drawbar Height 152 mm Width 76. 2 mm Thickness 12. 7 mm Front-top/bottom plate Width 305 mm Thickness 22 mm Front frame structure Height 321 mm Width 255 mm Front axle Height to center 600 mm Wheel lean, 18° left/right Front axle ­ total 32° oscillation per side 60. 2 in 1. 6 in Ripper Ripping depth, maximum Ripper shank holders Ripper shank holder spacing Penetration force Pryout force Machine length increase, beam raised 426 mm 5 533 mm 9386 kg 12 544 kg 1031 mm 16. 8 in 6 in 3 in 0. 5 in 12. 0 in 0. 87 in 12. 6 in 10 in 23. 6 in 21 in 20, 693 lb 27, 655 lb 40. 6 in · Front-top/bottom plate ­ width tolerance ±2. 5 mm (0. 098 in) 15 SH680/SH680 AWD Motor Grader Specifications Scarifier Front, V-Type: 1205 mm Working width Front, V-Type, 5 or 11 tooth Working width 1031 mm Scarifying depth, 467 mm maximum Scarifier shank 5/11 holders Scarifier shank 116 mm holder spacing Mid, V-Type Working width 1184 mm Scarifying depth, 292 mm maximum Scarifier shank 11 holders Scarifier shank 116 mm holder spacing Front, V-Type Scarifying depth, 1031 mm maximum Scarifier shank 5/11 holders Scarifier shank 467 mm holder spacing Rear Working width 2133 mm Ripping depth, 426 mm maximum Scarifying depth, 426 mm maximum Scarifier shank 9 holders Scarifier shank 267 mm holder spacing 47. 4 in Weights Gross Vehicle Weight, base Total 16 849 kg 37, 145 lb Front axle 4208 kg 9, 277 lb Rear axle 12 640 kg 27, 867 lb Gross Vehicle Weight, max Total 24 888 kg 54, 869 lb Front axle 7715 kg 17, 009 lb Rear axle 17 173 kg 37, 860 lb Operating Weight, typically equipped Total 19 224 kg 42, 383 lb 11, 989 lb Front axle 5438 kg Rear axle 13 786 kg 30, 394 lb Standards ROPS/FOPS Steering Brakes Sound ISO 3471/ISO 3499 ISO 5010 ISO 3450, ISO 10265 ISO 6394; ISO 6395 40. 6 in 18. 4 in 4. 6 in 46. 6 in 11. 5 in Weights ­ AWD 4. 6 in Gross Vehicle Weight, base Total 17 841 kg 39, 334 lb Front axle 4719 kg 10, 403 lb Rear axle 13 123 kg 28, 930 lb Gross Vehicle Weight, max Total 24 888 kg 54, 869 lb Front axle 7715 kg 17, 009 lb Rear axle 17 173 kg 37, 860 lb Operating Weight, typically equipped Total 20 116 kg 44, 349 lb Front axle 5915 kg 13, 040 lb Rear axle 14 201 kg 31, 309 lb · Base operating weight calculated on standard machine configuration with 14. 0R24 tires, full fuel tank, coolant, lubricants and operator. · Typically equipped operating weight is calculated with push block, rear ripper/scarifier, and other equipment. · The static sound operator sound pressure level measured according to ISO 6394:2008 for a cab offered by Caterpillar, when properly installed, maintained and tested with doors and windows closed and engine cooling hydraulic fan at maximum speed is 73 dB(A). · The dynamic spectator sound power level measured according to ISO 6395:2008 for the standard machine when equipped with optional sound suppression package and engine cooling hydraulic fan running at 70% of maximum speed, machine sound measured is less than 106 dB(A) for SH680 and 107 dB(A) for SH680 AWD, complying with EU 2000/14/EC requirement. 40. 6 in 18. 4 in 84 in 16. 8 in 16. 8 in 10. 5 in 16 Dimensions 1 10 9 8 11 12 13 7 6 3 5 4 2 1 Height ­ Top of Cab 2 Height ­ Front Axle Center 3 Length ­ Between Tandem Axles 4 Length ­ Front Axle to Moldboard 5 Length ­ Front Axle to Mid Tandem 6 Length ­ Front Tire to Rear of Machine 7 Length ­ Counterweight to Ripper 8 Ground Clearance at Rear Axle 9 Height to Top of Cylinders 10 Height to Exhaust Stack 11 Width ­ Tire Center Lines 12 Width ­ Outside Rear Tires 13 Width ­ Outside Front Tires 3287 mm 600 mm 1523 mm 2557 mm 6126 mm 8898 mm 10 140 mm 344 mm 3043 mm 3242 mm 2141 mm 2581 mm 2581 mm 129. 4 in 23. 6 in 60 in 100. 7 in 241 in 350. 3 in 399. 2 in 13. 5 in 119. 8 in 127. 6 in 84. 3 in 101. 6 in 101. 6 in Optional Tire Arrangements Tire Arrangement Weight (Total ­ 6 Tires) 1035 kg 2, 276 lb 1222 kg 2, 687 lb 1249 kg 2, 747 lb 1264 kg 2, 780 lb 1137 kg 2, 502 lb 1396 kg 3, 071 lb 1463 kg 3, 219 lb 1499 kg 3, 297 lb Wheel Group Tires 10x24 MP 14. 00R24 Michelin XGLA2 1 Star 10x24 MP 14. 0R24 Bridgestone VSW 1 Star 10x24 MP 14. 0R24 Bridgestone VKT 1 Star 14x25 MP 17. 5R25 Michelin XTLA 1 Star 14x25 MP 17. 5R25 Michelin XSNO Plus 1 Star 14x25 MP 17. 5R25 Michelin XHA 1 Star 14x25 MP 17. 5R25 Bridgestone VKT 1 Star 14x25 MP 17. 5R25 Bridgestone VSW 1 Star For a complete list of tire options, contact your local Cat dealer. 17 SH680/SH680 AWD Standard Equipment Standard equipment may vary. [. . . ]