User manual CATEYE CC-MT400

[. . . ] They may damage the surface of computer. Note Please read these instructions carefully before attempting to install and use your CAT EYE MITY 8 computer so that you understand the functions of this product. Please don't throw away this manual, Keep the manual at a place easily accessible. Computer Set-up (For 1st use or after replacing the battery) 3 1 All Clear Push three buttons (MODE, START/ STOP and SET) at the same time. * Do this procedure without fail for stable measurement when you use this system for the first time and every time the battery is replaced. SET Button SET Button Contact Point 1 2 3 5 6 4 7 1 Bracket 2 Cord 3 Sensor 4 Sensor Rubber Pad 5 Magnet 6 Bracket Rubber Pad 7 Nylon Ties (5) 2 1 5 Sensor Side Spoke START/STOP Button MODE Button START/STOP Button MODE Button 2 Select The Measurement Unit Select the measurement unit, kilometer or mile, by pushing the MODE button. ! You need to know the tire circumference (L cm) beforehand. 1 2 Mount the magnet 5 on a spoke of the front wheel so that the surface of the magnet will face the sensor. Kilometer MODE Mile Mount sensor and adjust the gap between the magnet and the sensor. Secure the sensor 3 with the larger nylon ties 7 at the appropriate place and in the right direction. Front Fork Choose Either of The Followings. · When you want to input the reading of the currently used odometer, keep pressing the MODE button for two seconds and input the reading. [. . . ] In Trip Distance 1, press and hold the Mode button to select Distance 2. You will continue to view this distance until you select Distance 1 with the same procedure. The computer can be programmed to run in either MANUAL MODE or AUTO TIME MODE. In Manual Mode you must press the START / STOP button to turn on and off the Timer, which records Distance and Average Speeds. In Auto Time the computer turns the Timer on and off depending on a signal from the sensor. When speed is detected by the computer and the Timer is running, the km/h or mph will flash. Speed will appear on the computer screen and the Odometer will record, regardless if the Timer is running or not. · Auto Time Mode (Automatic Measurement) In AUTO TIME mode, the letters will appear on the computer screen. Elapsed time, Average and Distance are recorded automatically and the Timer, stops when the speed stops. In this mode the START/STOP button is not operable. · Manual Measurements When you don't see the icon on the screen, you can start or stop the measurements by pushing the START/STOP button. When you push the button, measurements of Elapsed Time, Average Speed, Trip Distance 1 and 2 are started and they are stopped with the second push of the button. · How to set ON or OFF the auto-mode Push the SET button on the back side of the computer while Elapsed Time, Average Speed, Trip Distance 1 or 2 is displayed, then the icon is lit" (ON) or turned OFF. Resetting Elapsed Time, Trip Distance, Average Speed and Max Speed. Press and hold the MODE and START/STOP buttons for 2 sec. in either the Elapsed Time, Trip Distance 1, Average Speed or Maximum Speed functions to reset these functions. The Odometer and Trip Distance 2 are not reset. · Resetting Trip Distance 2 Trip Distance 2 is reset independently. When Trip Distance 2 is on the screen, press and hold both the MODE and START/STOP buttons to reset. Measurement Unit Icon Measurement Display Speed 0. 0 (4. 0) - 105. 9 km/h [0. 0 (3. 0) - 65. 9 mph] Power Saving Screen (When no signal is received for about one hour, the computer switches to the power-saving mode) When you push either of the MODE button or the START/STOP button or you ride the bicycle, the display comes back to the measurement display. Average Pace Arrow It shows that the current speed is faster or slower than the Average Speed. Faster Slower Auto-mode Icon Wheel Icon When it is lit, the measurements are automatically started or stopped. Indicates which wheel setting is selected. Mode Selection Illustrations (bottom of the screen) You can program two tire sizes and use either of them. Road MTB Av Average Speed 0. 0 -105. 9 km/h [0. 0 - 65. 9 mph] How to select tire size or When data other than Odo is displayed SET Keep on pressing the button for two seconds When the Odo data is displayed MODE Dst Trip distance - 1 0. 00 -999. 99 km [mile] Road MTB ST/STOP Trip distance - 2 MODE 0. 00 - 999. 99 km [mile] * Resetting of Dst2 only Keep on pressing buttons for 2 sec. at the same time Inputting the Tire Circumference Return to Odo SET SET ST/STOP SET Tm Av Dst MODE Range of setting: 100 - 300 cm Odo Odometer 0. 0 - 99999 km [mile] When the measurements are stopped Mx Maximum Speed MODE ST/STOP For 2 sec. [. . . ] Strange data appears Do all clear procedure (write down the number of Odometer if possible before doing the all clear procedure and input it manually after choosing the measurement unit). Measurements do not start when the START/STOP button is pushed. Turn the Auto-Mode off to enable the start or stop of the measurements by manual operation of the button. (If the speed data is not displayed, have the contact points short-circuited by a metal plate. [. . . ]