User manual CATEYE CS-1000

[. . . ] ----- Refer to "Sensor/Magnet Mounting" and re-adjust correctly. ----- Replace the Bracket & Sensor part with a new one. Transmission signal loss in damp or wet conditions. ----- Water or condensation may collect between the bracket sensor and the computer causing an interruption in the data transmission. [. . . ] 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546 Japan Attn. : CAT EYE Customer Service Section Service & Research Address for United States Consumers: CATEYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone: 303-443-4595 Toll Free: 800-5CATEYE Fax: 303-473-0006 e-mail: CatEyeUSA@aol. com #166-5120 Wheel Magnet #169-6180 Lithium Battery (CR1620) E OPERATING INSTRUCTIONS A. Main Display (Speed) Sensor Pulse Symbol Mode Symbol Speed Scale Symbol Auto Mode Symbol Sub-Display (Selected Function) M (Mode) Button H. S/S (Start/Stop) Button Set Button Battery Case Cover Contact 1. Sensor Band Screw Sensor Bands-A (S)(L) Sensor Bands-B Magnet Sensor Band Rubber Pad CA T EY E MOUNTING TO BIKE · The spokes must run correctly through the inside the magnet as in fig. 8. · Attach the sensor with Sensor Bands-A-B to the right fork. Choose a band that fits the fork diameter (S size for up to 24ø, L for oversize). Insert the band-B into the slit of the band-A, and put the rubber pad inside of the band-A(fig. Adjust the length in order that the screw-fastening part of the bands are parallel when mounted to the fork(fig. *To pull out the band B from band A, tug strongly. Mount the adjusted bands to the fork along with the sensor, by temporarily tightening the screw(fig. When the desired number appears, press M button. ODO will be displayed, and the desired number is set. ·Test (Fig. 16) Mount main unit. If main display does not show any figures, press either M button or S/S button to release from power saving function. Spin the wheel to check if sensor pulse symbol flashes. If not, adjust relative positions of magnet and sensor following the instructions. sensor band A sporkes sensor band B Fig. 6 (4) Resetting or changing the wheel circumference Set main unit in ODO with M button, and stop it with S/S button. The stored number will flicker on the sub-display. Revise the number as desired according to the instructions in (3). sensor band B rubber pad screw sensor band A parallel Fig. 10 sensor fork Fig. 11 bracket outer cable Setting the clock time (Fig. 7) Press M button over 2 seconds to select , and stop it with S/S button. Then press SET button, and minutes flash. Press S/S button to advance minutes by one. To advance rapidly, hold down the button. Set the time one or two minutes ahead of the current time. [. . . ] In Auto Function, this button is invalid. 12-hour clock time The current time is displayed by a 12-hour clock. 0:00' - 11:59' ±0. 003 % · SET Button This is for setting the wheel circumference and clock time, switching on/off Auto Function and to clear all present data and any irregularity. When pressed in stop state in each mode, the following can be revised. · In ODO mode --------------------- Wheel circumference · In mode ----------------------- 12-hour clock · In TM, DST or AVS mode ----- On/off the Auto function AUTO (AUTOMATIC START/STOP) FUNCTION DST AUTO Reset Operation: (Fig. 2) Select any mode except ODO, then press M button and S/S button simultaneously. (When done in ODO, registered wheel circumference will be displayed. ) RESET All Clear Operation: (Fig. 3) When M button, S/S and set buttons are pressed simultaneously, all data stored (ODO, speed scale, Wheel circumference and clock time) is erased. [. . . ]