User manual CATEYE CYCLOCOMPUTER

[. . . ] CATEYE ASTRALE CC-CD100 AT OMAD TSC CYCLOCOMPUTER Model CC-CD100N U. S. 4633216/4642606/5236759/5226340/5264791 and Design Patented Copyright© Aug. CCMCD1N-981118 0687281 7B Setting Values Cross Reference Table (The tire size is marked on both sides of the tire. ) Table de Correspondance des Valeurs de Réglage (La dimension du pneu figure de chaque côté du pneu) Wertetabelle zur Einstellung des Radumfanges (die Radgröße entnehmen Sie der Aufschrift des Reifens) Tabel voor het bepalen van de wielomtrek (de bandenmaat staat vermeld aan beide zijden van de band) Tabella delle Corrispondenze dei Valori di Regolazione (La dimensione del pneumatico figura su ogni lato del pneumatico) Tabla de Valores (El tamaño de la rueda está marcado al lado de la llanta) TIRE SIZE 20 x 1. 75 24 x 1 24 x 3/4 Tubular 24 x 1-1/8 Tubular 24 x 1-1/4 24 x 1. 75 24 x 2. 00 24 x 2. 125 26 x 1(559mm) 26 x 1(650c) 26 x 1. 25 LIMITED WARRANTY 1-Year Warranty for Main Unit Only (Accessories/Attachments and Battery Consumption excluded) If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. The service must be performed by Cat Eye Co. , Ltd. [. . . ] Pressing the Start/Stop button can shift the Current Speed to Cadence display. It will return to Current Speed display when Auto function is released. ·Setting the wheel circumference 1. How to measure the wheel circumference(Fig. 4) Fig. 2 Put a mark on the tire tread and ride the bike one full wheel revolution. Mark the start and the end of the revolution on the ground and then measure the distance between the two marks. Or, the "Selecting Values Cross Reference Table" tells you an approximate circumference according to tire size. POWER SAVING FUNCTION When the main unit is left without receiving any input for 60-70 minutes continuously, the power will be automatically saved. Then the main unit will display the clock time only as shown in the figure. Press either the Mode button or Start/Stop button to release Power Saving mode. (The Power Saving mode is automatically released when the main unit receives signal from the sensor. ) 2. Setting the wheel circumference Fig. 3 The figures 2155, standard wheel circumference for 27", will flicker as shown in fig. When using 2155mm without revision, press the Set button. Current Speed and Elapsed Time will be displayed and 2155mm is set. To revise 2155mm, press the Start/Stop button to increase the number by one or press the Mode button to decrease the number by one. When either button is held down, it will rapidly increase/decrease. Choose a correct circumference between 10mm to 2999mm. When the desire figure appears, press the Set button. Current Speed and Elapsed Time will be displayed, then the figure you selected will be set. TROUBLE SHOOTING · The following situations do not indicate malfunction of the cyclocomputer. Check the following before taking to repair. * When current speed does not appear, short-circuit the contact on the back with metal. The unit will function normally if the speed display appears. Display response is slow. Is it at a low temperature under 32°F(0°C)?It returns to normal state when temperature rises. Has the Lithium Battery in the main unit worn out? [. . . ] In the above cases, press AC button so that display / buttons returns to normal. (If AC button is pressed, all the data including odomater is erased. Please refer to "Main Unit Preparetion" in the operating instructions. ) CLOSE OPEN CR2032 Specifications Applicable Cycle Sizes Applicable Fork Diameter Power Supply Battery Life Dimension/Weight 10 mm to 2, 999 mm 11ø - 36ø (S:11-26ø L:21-36ø) Lithium Battery (CR2032x1) Appro. 3 years (The life of the first factory-loaded battery may be shorter) 1-15/16"x 1-25/32"x 11/16"(49 x 45 x 17 mm) / 0. 9 oz(25. 5 g) Fig. 6 *The specifications and design are subject to change without notice. Wire Securing/Bracket Mounting Outer Cable Mounting To Bike CYCLOCOMPUTER MODEL CC-CD100 R Wheel Sensor/Magnet Mounting Wheel Magnet Wire Wire Securing Tape 1 Wire Clip Wire Wire Clip 2 Screw Bracket (1) Clamp the wire with the wire securing tape and wire clip as shown in Fig. 1 &2. [. . . ]