User manual CENTURION D3

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CENTURION D3. We hope that this CENTURION D3 user guide will be useful to you.

Lastmanuals help download the user guide CENTURION D3.


Mode d'emploi CENTURION D3
Download
Manual abstract: user guide CENTURION D3

Detailed instructions for use are in the User's Guide.

[. . . ] - Position baseplate (43) with centre of single support stud (45) 105mm from edge of gate (46). (This dimension assumes centre line of rack (47) is 20mm from edge of gate). - Using the baseplate as a template mark and drill the 4 mounting holes into the concrete for the four M10 x 95 expansion studs. - Use two M12 plated nuts per expansion stud as spacers below the foundation plate. [. . . ] - Manually slide gate OPEN until origin marker (66) is in line with the origin sensor (68). Ensure distance between face of marker (66) and front face of sensor (68) is between 13 and 20mm. (See (C) above) - Adjust distance by sliding the origin marker (66) along the slotted mounting holes until desired distance is achieved. Not necessary but if fitted then CP80 PSU1 controller 12 16 CP80 / CP81 TRG PED LCK LED FRX LIGHT LIGHT COM COM +12V SET IRB NEG 12V N/O 22 COM NEG 23 12V NEG 12V N/C 24 COM 25 26 27 28 29 SIGNAL WIRING (CP80 AND CP81) 22 23 24 25 26 27 28 29 - RADIO RECEIVER (OR OTHER TRIGGER e. SHOWING STATUS OF INPUT SIGNALS † = USE MULTI LED DRIVER CARD (CP78) FOR MORE LED’S 17 31 34 50 ENL 220V AC LNE INPUT 220V AC OUTPUT TO CP80/CP81 PCB "DC IN” 49 43 48 RECOMMENDED LIGHTNING PROTECTION - For optimum lightning protection ensure earth cable from charger/PSU unit 34 is adequately earthed. - In event of damage to charger/PSU unit 34 disconnect quick release link 50 and push-on connector on controller. 29-30) 5 Steps 1 to 3 must be done on initial commissioning. 8V STATUS STATUS STATUS SET SET 72 SET BLACK RED 69 71 70 SELECTING PROGRAMME MODE STEP 1 - Remove power from control card: - for A5 remove electronics power only 69 - for D3/D5 remove battery power 70 as well as electronics power 69 . STATUS LED will flash 5 times on power up. Check that LED L2 and “SET” are ON. 2 SETTING GATE LIMITS - Rotate manual release thumbwheel 37 fully clockwise, or until clutch is fully dis-engaged and gate can be moved by hand. D3/D5 ONLY - Slide gate approximately half way open. A5 ONLY - Slide gate to fully closed position (FIG. Ensure you follow the correct procedure!The procedure for setting D3/D5 and A5 motors is DIFFERENT. The A5 limits have to be set manually (see page 25 and 26), while the D3/D5 motors set their limits automatically (see page 21 to 23). D3/D5 ONLY (PAGE 23, 24, 25) - Press the TEST pushbutton while monitoring LED L1. - When L1 flashes once, release TEST pushbutton. L2 will go out, L1 will continue to flash once per second. Controller is now in MENU 1 which sets gate limits. Understand the procedure detailed on page 24 before continuing. The controller is about to perform the fully automatic setup routine. [. . . ] sTEP 4 - Release TEST button when the required main menu (see Table 2 , page 28) is selected. STEP 5 - To select the sub-division of the main menu (see RHS of Table 2), press and hold the TEST pushbutton, while monitoring the STATUS LED to count flashes. The number of times the STATUS LED flashes represents the sub menu number. sTEP 6 - Release TEST pushbutton when the required subdivision is selected. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CENTURION D3

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CENTURION D3 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag