User manual CHAFFOTEAUX & MAURY BRITONY COMBI SE 100 NAT

[. . . ] COMBINATION BOILER Heating and Instantaneous Domestic Hot Water Fanned Flue system Installation and Operating instructions These instructions Must Be Left With The Appliance. 2 1 0 bar 3 4 2 1 0 bar 3 4 c Manufactures N° 200906812037. 31 200906812027. 31 200906813037. 31 200906813027. 31 Model Type Britony SE 80 Nat Britony SE 80 L. P. G. Britony SE 100 Nat Britony SE 100 L. P. G. Gas Council N° 47 - 980 - 16 47 - 980 - 18 47 - 980 - 17 47 - 980 - 19 GB IE c These instructions are suitable for the following boilers : Britony Combi SE. 80 Britony Combi SE. 100 Do not forget the Log Book!Chaffoteaux & Maury supports Benchmark, the heating industry code to ensure the correct installation, commissioning and servicing of domestic central heating systems. [. . . ] Suitable guards may be obtained from the following manufacturer: Quinnel Barret & Quinnel Wireworks Old Kent Road London SE15 1NL Tel: 0171 639 1357 Ventilation The room in which the boiler is installed does not require specific ventilation. If it is installed in a cupboard or compartment permanent ventilation is not required for cooling purposes. Gas Supply The gas installation and soundness testing must be in accordance with the requirements of BS 6891. The boiler requires a 22 mm supply. Ensure that the pipe size is adequate for demand including other gas appliances on the same supply. Electrical Supply The appliance requires an earthed 230V - 50 Hz supply and must be in accordance with current I. E. E. It must also be possible to be able to completely isolate the appliance electrically. Connection should be via a 3 amp fused double-pole isolating switch with contact separation of at least 3 mm on both poles. 3 pin plug and unswitched socket may be used, provided it is not used in a room containing a bath or shower. It should only supply the appliance. Location The boiler can be installed on any suitable internal wall. Provision must be made to allow the correct routing of the flue and siting of the terminal to allow the safe and efficient removal of the flue products. A compartment or cupboard may be used provided that it has been purpose-built or modified for the purpose. It is not necessary to provide permanent ventilation for cooling purposes. Detailed recommendations are given in BS 5440 pt 2. If it is proposed that it is installed in a timber framed building then reference must be made to British Gas Document DM2, or advice sought from CORGI. Flue Detailed information on flue assembly is contained in the appropriate starter pack. The boiler must be installed so that the flue terminal is exposed to the free passage of external air at all times. It must not be allowed to discharge into another room or space such as an outhouse or closed lean-to. The minimum acceptable clearances are shown below: - A Directly below an opening, window, etc - B Above an opening, window, etc - C Horizontally to an opening, window, etc - D Below gutters, soils pipes or drain pipes - E Below eaves - F Below balconies or car port roof - G From a vertical drain pipe or soil pipe - H From an internal or external corner - I Above ground roof or balcony level - J From a surface facing the terminal - K From a terminal facing the terminal - L From an opening in the car port into the dwelling - M Vertically from a terminal on the same wall - N Horizontally from a terminal on the same wall - Q Fixed by Ubbink Rolux 4 GM flue terminal 300 mm 300 mm 300 mm 75 mm 200 mm 200 mm 150 mm 300 mm 300 mm 600 mm 1200 mm 1200 mm 1500 mm 300 mm Q Q I F J B L G A I C H H N M N M D, E Q K Fig. 8 7 Installation Installing the Boiler Method of positioning the boiler on the wall. The paper template can be used to ensure the correct positioning of kitchen cabinets etc. The paper template has to be fixed to the wall and used to locate the position of the hanging bracket, the centre for the flue hole and, if required, the fixings for the pre-piping jig. Drill and plug the wall and secure the hanging bracket using the screws provided. [. . . ] will light. 1) Turn main switch 19 to position I . The green "power on" indicator 23 indicator will light 28. 2) Turn on a hot water tap, the orange "burner on" indicator will light 24 and the water will become hot. The DHW 13 11 Instruction for Setting the Built in Clock (if fitted) 1. [. . . ]