User manual CHAMBERLAIN 810EML INSTALLATION

[. . . ] Your new operator is capable of operating up to 12 cycles per hour or 50 cycles per day. It is equipped with a built in radio receiver that is compatible with our existing 315 MHz product line as well as a Timer-to-Close (TTC) feature that can be enabled when LiftMaster Commercial Protector System® is installed and aligned properly. BASIC PROGRAMMING INTRODUCTION TO PROGRAMMING Many programmable functions require that a LiftMaster Entrapment Protection (LMEP) device be installed in order to function. Refer to the Entrapment Protection section. LOGIC BOARD OVERVIEW DATA SLOT Optional Auxiliary Card Receptacles 1 SLOT 24VAC 2 POWER Motor Direction Jumper Maximum Run Timer Button OLS MID SLS CLS MRT MID TTC TIMER ENABLE 24VAC TIMER DEFEAT 1-PHASE 3-PHASE COMMON MAS Single Phase & Three Phase Jumper Maintenance Alert System Button for Programming REV STD MOTOR DIRECTION Radio Learn Button LMEP: EDGE: OPEN Open Button Close Button RADIO 1 2 3 CLOSE Mid Stop Learn Button STOP Stop Button T E2 D1 TS FSTS DIAG OPTN PROG COMMON Timer-To-Close Learn Button C2 B2 Control Wiring Terminal Block SBC RELAY RELAY A B Selector Dial (used for programming and selecting wiring type) Main Motor Control Harness Connection LOGIC BOARD LED OVERVIEW NOTE: Before programming the logic board, set the operator's open and close limits. [. . . ] When in E2 mode, the door will move to the fully open position. 3 BASIC PROGRAMMING WARNING To prevent possible SEVERE INJURY or DEATH: · Install a LiftMaster Monitored Entrapment Protection (LMEP) device. · NEVER permit children to operate or play with door control push buttons or remote controls. · Activate ONLY when it can be seen is properly CAUTION door there are no obstructions toclearly, travel. adjusted and door · ALWAYS keep door in sight until completely closed. NEVER permit anyone to cross the path of closing door. REMOTE CONTROLS Built in 3-channel, 315 MHz radio receiver allows you to add as many as 23 Security® remotes or dip switch remote controls. NOTE: The following programming requires a LiftMaster Monitored Entrapment Protection (LMEP) device. SINGLE BUTTON REMOTE CONTROL 1 MID SLS CLS MRT MID TTC Press and release the RADIO button (RADIO LED will light). until 2 Press and hold the remote control buttonremotethe 3 AVERTISSEMENT RADIO LED flashes rapidly, then release control button. The RADIO LED will then remain on solid after releasing the button. Repeat to add additional remote control(s). MID SLS CLS MRT MID TTC TIM ENA TIM ENA RADIO 1 2 3 ATTENTION RADIO 1 2 3 Press and release the RADIO button to complete the programming. The programming mode is exited if no activity is performed within 30 seconds. AVE ASE ASE MOTOR DIRECTION 3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION NOTE: The feature will use 3 of the 23 memory channels in the operator. MOTOR DIRECTION AV T E2 TS FSTS E2 T TS FSTS 1 MID SLS CLS MRT MID TTC TIM ENA RADIO 1 2 3 Press and release the RADIO button on the logic board (the Radio LED will light). 2 LMEP: TTC TIMER ENABLE EDGE: OPEN 3 CLOSE STOP FSTS DIAG T E2 TS FSTS OPTN COMMON Press and release the desired button on the logic board (OPEN, CLOSE or STOP). The Radio LED will flash and then stay on solid. 3 HASE Press and hold the desired button of the remote control until Radio LED flashes rapidly, then release. Repeat steps 1 through 3 to program additional buttons. TO ERASE ALL REMOTE CONTROLS MOTOR DIRECTION ADVERTENCIA AD PRECAUCIÓN 1 A HASE MID SLS CLS MRT MID TTC TIM ENA RADIO 1 2 3 T E2 TS FSTS Press and hold the RADIO button on the logic board until the RADIO LED flashes rapidly (approximately 5 seconds). All remote controls will be erased. MOTOR DIRECTION 4 BASIC PROGRAMMING WARNING To prevent possible SEVERE INJURY or DEATH: · Install a LiftMaster Monitored Entrapment Protection (LMEP) device. Press and hold TIMER button for 5 seconds until OPEN and OLS flashes then release. Press and release the OPEN button and wait for the door to reach full open or mid stop position. Wait for desired amount of time to pass. (An internal stop watch starts counting when the door stops moving. ) 6. Press and release the TIMER button, CLOSE button or STOP button to stop the timer. Turn the selector dial to the desired wiring type (T, TS, FSTS). NOTE: To read back the Timer-To-Close setting, turn the selector dial to DIAGNOSTIC and press the TIMER button. The OPEN LED will flash once for every second programmed and the CLOSE LED will flash once for every 15 seconds programmed. To deactivate the timer from the open position press the STOP button. The timer will be reactivated on the next operation command. To deactivate the timer for more than one cycle, attach a switch to 11 and 12 (Common and Timer Defeat). [. . . ] Verify photoelectric sensors are aligned. Verify photoelectric sensors are aligned. If photoelectric sensors are aligned and operator still does not operate properly, contact your installing dealer. OPERATOR WILL NOT RESPOND TO ANY No power COMMANDS Accessory failure Possible component failure OPERATOR MAKES NOISE BUT DOOR DOES NOT MOVE DOOR DRIFTS AFTER OPERATOR STOPS DOOR OPENS/ CLOSES TOO FAR DOOR REVERSES UNEXPECTEDLY RADIO FUNCTIONALITY Operator requires adjustment Operator or door requires adjustment Operator requires adjustment Entrapment protection device activated NO RESPONSE Remote control is not programmed Low battery See PROGRAMMING REMOTE CONTROLS section. Contact your installing dealer. REMOTE CANNOT BE PROGRAMMED POOR RANGE Low battery Low battery in remote Possible radio interference G MAINTENANCE SCHEDULE WARNING WARNING To avoid SERIOUS personal INJURY or DEATH: · Disconnect electric power BEFORE performing ANY adjustments or maintenance. [. . . ]