User manual CHAMBERLAIN CPWR

[. . . ] Turn screws counterclockwise 1/4 turn and remove front cover. Before or while touching the circuit board, discharge any static electricity: (1) Use a grounding strap OR (2) Touch a cold, grounded, metallic pipe. The output code format switch settings are factory-set for the 30-bit format (Figure 2). [. . . ] Facility Code Factory Setting = All OFF (switches set to left). INSTALLATION AND WIRING 1. Mount receiver to surface using #6 hardware (not provided). (Figure 8) NOTE: Mount receiver with 18" of space above the receiver for the antenna. The receivers should be installed at least 5' apart to avoid "cross-talk". Screw on antenna clockwise and slide rubber boot down to meet o-ring (Figure 7). Remove the terminal block from J2 on the circuit board. Connect wires from the CPWR 6-pin connector to the access control system (Figure 8). Then re-insert the terminal block onto J2. Wire the CPWR to the access control systems' card reader port. Refer to the access control system's instructions for appropriate wiring detail. A typical wire connection might resemble the following: CABLE SIGNALS LED DATA 1 DATA 0 +12VDC COMMON (GND) SHIELD WIRE COLOR BROWN WHITE GREEN RED BLACK SHIELD The outside of the antenna connector is not ground. If using an extension kit, do not allow it to contact a metal object. Figure 7 U1 C2 2 Y2 L3 C9 C13 R1 L1 C17 L2 C10 C11 J1 C14 Y1 E1 D11 C9 C23 C20 C18 Y4 C15 C33 C34 C12 C16 R5 C19 R4 U6 R10 C27 L4 R22 Y3 C21 C2 SIGNAL D12 D13 C26 1 C29 DA A T C25 14 U2 R21 C2 R2 R3 R7 R24 R23 A VLID D9 Mounting Holes R6 Q4 R11 CLOCK IN 1 U7 R25 R26 TP4 POWER D1 GRANTED C3 U5 FACILITY 1 C5 CO D E 6 4 2 0 7 5 3 1 TP1 R8 C28 R12 DATA IN FORMAT 3 2 1 0 Q1 3 2 BUTTON 1 C30 C31 14 U3 J3 +5V GND TP3 U12 Mounting Holes NOTE: At power up, the CPWR will perform a system check and produce a series of LED flash sequences (this is normal). 1 15 14 13 12 11 10 9 8 C4 Q2 R19 D7 D6 D5 R20 TP2 C32 FFC D2 U9 14 RP2 1 U4 C7 U10 RP3 1 C8 U8 RP1 1 C6 D8 D3 R17 R16 R14 R13 D3 R15 D16 MADE SENTEX SYSTEMS I N USA R10 D4 J2 To Access Control Circuit Board (Reader Port) Figure 8 3 TESTING AND TROUBLESHOOTING 1. Ensure that the red POWER LED is lit (Figure 9). If not, check your power connections and/or source. Voltage reading should be within the range of 9VDC ­ 18VDC. The SIGNAL LED (Figure 9) should be flickering continuously, indicating that the RF receiver circuitry is operating. Press the transmitter button previously set in step 4, page 3, within view of the receiver. If the DATA-yellow and VALID-green LEDs do not light, review the Setting the Switches and Connect Signal/Power Wires sections. [. . . ] Attach front cover of receiver by turning screws clockwise 1/4 turn. Call your local power company if interference is due to arcing power lines. U1 C22 Y2 L3 C9 C13 R1 L1 C17 L2 C10 C11 J1 C14 Y1 E1 D11 C9 C23 C20 C18 Y4 C15 C 33 C 34 C12 C16 R5 C19 R4 U6 R1 0 C27 L4 R 22 Y3 C21 C2 SIGNAL D12 R 23 C 26 1 C29 DATA D13 14 U2 R7 U7 R6 Q 4 R11 R2 1 C25 C2 R2 R3 R2 4 VALID D9 POWER D1 CLOCK IN 1 R25 R 26 TP4 GRANTED C3 U5 FACILITY 1 C5 CO D E 6 4 2 0 7 5 3 1 TP1 R8 C28 R12 DATA IN FORMAT 3 2 1 0 Q1 3 2 BUTTON 1 C30 C31 14 U3 J3 +5V GND TP3 U12 1 15 14 13 12 11 10 9 8 C4 14 RP2 Q2 R19 D7 D6 D5 R20 TP2 C32 FFC D2 U9 1 C7 U10 RP3 1 C8 U8 RP1 1 C6 D8 D3 R17 R16 R14 R13 D3 R15 U4 D16 MADE SENTEX SYSTEMS I N USA D11 SIGNAL D12 DATA D13 VALID D9 POWER D1 GRANTED Figure 9 4 R 10 D4 APPENDIX: FACILITY CODE SWITCH SETTINGS Refer to Figure 1 on page 1 for the facility code DIP switch location. Also, when setting the receiver's DIP switches, refer only to the numbers silk screened on the PC board (not the numbers on the DIP switch itself). FC 5 4 3 2 1 0 000 0 0 0 0 0 0 001 0 0 0 0 0 1 002 0 0 0 0 1 0 003 0 0 0 0 1 1 004 0 0 0 1 0 0 005 0 0 0 1 0 1 006 0 0 0 1 1 0 007 0 0 0 1 1 1 008 0 0 1 0 0 0 009 0 0 1 0 0 1 010 0 0 1 0 1 0 011 0 0 1 0 1 1 012 0 0 1 1 0 0 013 0 0 1 1 0 1 014 0 0 1 1 1 0 015 0 0 1 1 1 1 FC 5 4 3 2 1 0 016 0 1 0 0 0 0 017 0 1 0 0 0 1 018 0 1 0 0 1 0 019 0 1 0 0 1 1 020 0 1 0 1 0 0 021 0 1 0 1 0 1 022 0 1 0 1 1 0 023 0 1 0 1 1 1 024 0 1 1 0 0 0 025 0 1 1 0 0 1 026 0 1 1 0 1 0 027 0 1 1 0 1 1 028 0 1 1 1 0 0 029 0 1 1 1 0 1 030 0 1 1 1 1 0 031 0 1 1 1 1 1 FC 5 4 3 2 1 0 032 1 0 0 0 0 0 033 1 0 0 0 0 1 034 1 0 0 0 1 0 035 1 0 0 0 1 1 036 1 0 0 1 0 0 037 1 0 0 1 0 1 038 1 0 0 1 1 0 039 1 0 0 1 1 1 040 1 0 1 0 0 0 041 1 0 1 0 0 1 042 1 0 1 0 1 0 043 1 0 1 0 1 1 044 1 0 1 1 0 0 045 1 0 1 1 0 1 046 1 0 1 1 1 0 047 1 0 1 1 1 1 FC 5 4 3 2 1 0 048 1 1 0 0 0 0 049 1 1 0 0 0 1 050 1 1 0 0 1 0 051 1 1 0 0 1 1 052 1 1 0 1 0 0 053 1 1 0 1 0 1 054 1 1 0 1 1 0 055 1 1 0 1 1 1 056 1 1 1 0 0 0 057 1 1 1 0 0 1 058 1 1 1 0 1 0 059 1 1 1 0 1 1 060 1 1 1 1 0 0 061 1 1 1 1 0 1 062 1 1 1 1 1 0 063 1 1 1 1 1 1 5 LIMITED WARRANTY LiftMaster warranties the receiver against original manufacturing defects for a period of three (3) years, measured from the day of initial shipment by LiftMaster. [. . . ]