User manual CHAMBERLAIN DIAL CODE VF

[. . . ] DIAL CODE SERIES O W N E R S M A N U A L Telephone entry systems with two line large LC or VF displays with BUILT-IN surge suppression VISIT US ON THE WEB www. chamberlain. com TABLE OF CONTENTS Product Overview . 4 LC Entry Phone Features Inside / Outside . 5-6 VF Entry Phone Features Inside / Outside . 11 Description of Surge Suppression Terminal Board . [. . . ] Please refer to the owners manual for proper grounding instructions. eliteentryphone. com MADE IN USA Ground (-) (+) POWER Use 22 AWG Twisted Pair Shielded Wire GATE RELAY DOOR RELAY Keypad RS485 Remote Device 1 Stand-Alone Receiver RS485 Remote Device 2 Card Reader RS485 Remote Device 3 Universal Interface Board RS485 Remote Last Device LC/VF Page 18 RS485 STAR CONNECTION EXAMPLE Remote Access RS485 COMMUNICATOR CARD Use 22 AWG Twisted Pair Shielded Wire (+) (-) Ground Keypad RS485 Remote Device 1 capacity Elite Entry Phone Main M ard Slot RS485 Memory Card Slot RS485 Card Release Button Stand-Alone Receiver RS485 Remote Device 2 NOTE: To support RS485 devices you must insert the RF communicator card in the RS485 memory card slot BEFORE turning on the processor. (+) (-) Ground TEL LINE TIP RING (+) (-) GND (+) (-) GND (+) (-) GND (+) (-) GND CHASSIS GROUND 12V AC/DC POWER INPUT Universal Interface Board RS485 Remote Device 3 RS485 (1) RS485 (2) DOOR-NO DOOR-NC DOOR-C GAE-NO T GAE-NC T GAE-C T DOOR RELA Y GAE T RELA Y RS485 (3) VCR-NO VCR-C GND INPUT VCR RELA Y POST L/EXIT A SW INPUT RS485 (4) (+) (-) Ground It is MANDAOR that this unit is properly TY grounded. The provided "chassis ground" wire must be connected to the ground rod. If unit is not grounded, lightning damage will occur . Please refer to the owners manual for proper grounding instructions. eliteentryphone. com MADE IN USA Card Reader RS485 Remote Device 4 POWER GAE T RELA Y DOOR RELA Y (+) (-) Ground LC/VF Page 19 MEMORY CARD INSTALLATION Main Memory Card Slot Turn power on and insert Memory Card into Main Memory Card Slot (Main Memory Card in back slot, Backup Memory Card in front slot. ) (fig a. ) Push it all the way in until card "snaps" into place and the release button pops up. The screen should display the "Welcome Screen" (fig b. ) RS 485 Memory Card Slot Main Memory Card Release Button (fig a. ) WELCOME (fig b. ) If the screen continues to display the "Insert Memory Card" screen (fig c. ) then eject memory card by pressing the corresponding release button down and reinsert Memory Card into main slot (fig d. ). Otherwise continue with programming. Push Button Insert Memory Card IN MAIN SLOT (fig c. ) Card Pops Out (fig d. ) VIEWING THE SOFTWARE VERSION Memory Capacity To view the memory capacity of the system or to view the software version currently running on the system in operation an information screen is accessible on all Dial Code systems for easy reference. Turn power off and insert Memory Card in Main Memory Slot. Turn power on and the information screen should display as seen in (fig e. ) LC/VF Page DIAL CODE LC-250 REV. 1. 00_ (fig e. ) Software Version Number 20 WARNINGS AND PRECAUTIONS 25 0 500 Do not touch the terminals on the RAM Cards. Do not bend, drop or expose to impact. 3 2 1 4 7 U Y T R E W Q A SHIF T BA R 6 5 8 0 I O L K J H M N CK BAACE SP 9 P HEL ENT PROG RAM P ER ' EX ERA SE T G F B V C D S X Z S E PAC The Telephone Entry System is only water resistant when the Stainless Steel Door is closed and locked. Do not expose the Processor Unit or the open Processor Containment Box to rain, snow, or harsh weather conditions. Do not drop the Processor or expose it to impact. LC/VF Page 21 PROGRAMMING THE PROCESSOR ENTERING THE PROGRAM MODE When the Processor unit is turned on and the button is pressed, the screen will display: TO ENTER PROG MODE, Type Password >____ Type in the factory present password (7777). The Program Selection Screen SELECT PROG MODE: (N)Names (U)Utility If you enter the wrong password, the screen will prompt you to try again: INVALID PASSWORD (R)Retry (EXIT)Quit Press R to retry entering your password. Press to quit the programming menu. Pressing the button will provide users with a help message. IMPORTANT NOTE: While in the help screens, programming will be disabled. To continue programming, press the button to exit the help screens first. LC/VF Page 22 SELECTING PROGRAM MODE LIST OF PROGRAM MODES: 1 2 3 4 5 6 7 8 9 Names Utility Password* Clock/Timer Strike Time Talk TIme Greeting Volume Backup N U P C S T G V B Program or edit Resident Names Program or edit Utility Codes Program New Password ( recommended ) Program System Clock and Seven Day Timers Program relay output time ( for 2 relays ) Program length of Talk Time Program custom Welcome Screen Message Program Volume level Backup of memory card page 24-26 page 27 page 28 pages 29-31 page 32 page 32 page 33 page 33 page 34 *We recommend you customize your password to avoid unauthorized programming (see "Password" section) To select a Program Mode, press the corresponding letter from one of the nine options. Use the keys to scroll through the nine different Program Modes. SELECT PROG MODE: (N)Names (U)Utility SELECT PROG MODE: (P)Password SELECT PROG MODE: (C)Clock/Timer SELECT PROG MODE: (S)Strike Time SELECT PROG MODE: (T)Talk Time SELECT PROG MODE: (G)Greeting SELECT PROG MODE: (V)Volume (B)Backup Pressing the button will provide users with a help message. IMPORTANT NOTE: While in the help screens, programming will be disabled. To continue programming, press the button to exit the help screens first. LC/VF Page 23 RESIDENT INFORMATION STEP 1 In the Program Selection Screen (fig a. ), Press the N key. The screen will display (fig b. ): SELECT PROG MODE: (N)Names (U)Utility (fig a. ) STEP PROG A NEW NAME PROG BY CODE:___ N (fig b. ) 2 N You now have three options: To program by code, enter To view or edit an existing name To program by name, press the key and the first OR a three digit code* and press the key. OR or code, use the keys to scroll through Directory. empty code will display. * The unit will only accept codes within it's range - depending on memory capacity. STEP 3 Type in the desired Resident name, LAST name first, followed by the first name (fig c. ). If the code you have selected is already used, there will be a name already. You can edit the name by simply typing over it. You may also use the keys to move the cursor Resident code 005 LastNAME, First Jones, Robert_ Resident name (example - fig c. ) 005 PHONE NUMBER: _-___-496-2634 (example - fig d. ) STEP 4 5 Type in the desired Resident phone number (fig d. ). If you need to enter an area code refer to the area code page. The "KEY CODE" screen will be displayed. [. . . ] If the power is off on the processor, the battery will not be charging. LC/VF Page 35 LC ILLUSTRATION & PARTS LIST T010 T009 T035 T060 T033 T011 TEL L NE Remote Access RS-485 TIP RING (+) () GND (+) () GND (+) () GND (+) () GND CHASS S GROUND 12V AC/DC POWER INPUT COMMUNIC TOR CARD RS 485 (1) capacity RS 485 (2) El te Entry Phone DOOR NO DOOR NC DOOR C GATE NO GATE NC GATE C DOOR RELAY GATE RELAY T031 T037 T003 T029 T002 Memory Card T020 T030 RS485 Card RS 485 3) VCR NO VCR C GND INPUT VCR RELAY POSTAL/EXIT SW INPUT 5 4) T027 LC Processor T044 T014SPT T025 T012SPT T032 T000 T026 LC Part # T000 T002 T003 T009 T010 T011 T012SPT T014SPT T020 T025 T026 T027 T029 T030 T031 T032 LC Description Transformer 12 Vac 50VA (Provided) External Keypad Keylock Processor Containment Box (Back Box) Processor Key Release / Lock Battery Back-Up 9-Pin Comm Port Connector (Surge Protection Terminal) External Box Connection Kit (Surge Protection Terminal) LC Complete Internal Metal Box (Processor Box) Programming Keys Postal Lock Assembly LCD Processor - No Memory Card Key for Internal / External Lock LCD Display Kit for Keypad Light Phone Control Board (Inside Processor) LC Part # T033 T035 T036 T037 T044 T060 T25MEM T50MEM T150MEM T250MEM T500MEM T1000MEM RFCARD4K RFCARD8K RFCARD16K LC Description LCD Display Window LC External Box Assembly Heater Pad Option (Pre-Installed in Processor) Keypad Light Speaker 4 OHM Dial Code Surge Protection Board 25 Name Memory Card 50 Name Memory Card 150 Name Memory Card 250 Name Memory Card 500 Name Memory Card 1000 Name Memory Card RS485 Communicator Card 4000 RS485 Communicator Card 8000 RS485 Communicator Card 16000 All components and specifications are subject to change without notice. LC/VF Page 36 VF ILLUSTRATION & PARTS LIST T010 T009 T034 T008 T005 T007 T060 T004 T011 T006 TEL L NE Remote Access RS-485 TP RING (+) () GND (+) () GND (+) () GND (+) () GND CHASSIS GROUND 12V AC DC POWER INPUT COMMUN CATOR CARD RS 485 1) capacity RS 485 2) El te Entry Phone Memory Card T019 T018 RS485 Card DOOR NO DOOR NC DOOR C GATE NO GATE NC GATE C DOOR RELAY GATE RELAY T031 T037 T003 T029 T002 RS 485 3) VCR NO VCR C GND NPUT VCR RELAY POSTAL EX T SW INPUT 485 4 T028 VF Processor T044 T014SPT T025 T012SPT T032 T000 T026 VF Part # T000 T002 T003 T004 T005 T006 T007 T008 T009 T010 T011 T012SPT T014SPT T018 T019 T025 T026 T028 VF Description Transformer 12 Vac 50VA (Provided) External Keypad Keylock Display Window Glass Only (VF) Display Window Metal Bracket (VF) Display Window Glass and Bracket (VF) Display Hood (VF) Stainless Steel Door (VF) Processor Containment Box (Back Box) Processor Key Release / Lock Battery Back-Up 9-Pin Comm Port Connector (Surge Protection Terminal) External Box Connection Kit (Surge Protection Terminal) Vacuum Florescent Display VF Complete Internal Metal Box (Processor Box) Programming Keys Postal Lock Assembly VFD Processor - No Memory Card VF Part # T029 T031 T032 T034 T036 T037 T044 T060 T25MEM T50MEM T150MEM T250MEM T500MEM T1000MEM RFCARD4K RFCARD8K RFCARD16K VF Description Key for Internal / External Lock Kit for Keypad Light Phone Control Board (Inside Processor) VF External Box Assembly Heater Pad Option (Pre-Installed in Processor) Keypad Light Speaker 4 OHM Dial Code Surge Protection Board 25 Name Memory Card 50 Name Memory Card 150 Name Memory Card 250 Name Memory Card 500 Name Memory Card 1000 Name Memory Card RS485 Communicator Card 4000 RS485 Communicator Card 8000 RS485 Communicator Card 16000 All components and specifications are subject to change without notice. LC/VF Page 37 APPROVALS The Chamberlain Group, Inc. Complies with Part 68, FCC Rules FCC Part 15 - Tested to comply with FCC standards for home or office use This Class B digital apparatus meets all requirements of CANADIAN Interference Causing Equipment Regulations. UL STD 294, 5th Ed. UL STD 1950, 3rd Ed. Instruction to the User: This equipment has been tested and found to comply with the limits for a class 13 digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]