User manual CHAMBERLAIN EGJ

[. . . ] FACTORYSET C2 Wiring See page 7 for other wiring configurations OWNER'S MANUAL EGJ EUROPEAN STYLE GEARHEAD DAMP ENVIRONMENT JACKSHAFT TH E C EL HA MH MB UR ER ST, LA IL IN G LIN R OIS OU 60 P, IN 12 C. 6 41 B6 PL LIS AC E RA TI NG LA BE L HE RE TE D DO OR OP ER AT OR 2 YEAR WARRANTY NOT FOR RESIDENTIAL USE Serial # Box Installation Date Wiring Type TABLE OF CONTENTS SPECIFICATIONS Operator Specifications . . 9 DIAGRAMS 1 Phase Schematic Diagram . . 4 Entrapment Protection Accessories (Optional) . [. . . ] Be sure that the power supply is of the correct voltage, phase, frequency, and amperage to supply the operator. Refer to the operator nameplate on the cover. IMPORTANT NOTE: For best protection against the environment follow directions below for required specifications for power and control wiring connections. system can be achieved, and optimum performance ensured, by adherence to simple conduit preparation and assembly techniques: 1. Square off ends of conduit by cutting the end of the conduit squarely using a hacksaw or similar tool, conduit manufacturers sometimes offer cutting jigs for this purpose. Insert conduit flush with the fitting end stop. A compression gland nut, when provided as part of a fitting, will typically achieve maximum securement. Ensure conduit jacket is not cut or ripped in any location along its surface. NOTE: For conduit preparation, always follow the conduit manufacturer's instructions. CIA CONDUIT & FITTINGS ADVERTENCIA ADVERTENCIA entry hole to be placed in enclosure and Liquid tight Flexible Non-metalics Conduit (LFNC) is required for 1. Select proper fitting use in both exposed and concealed areas and for electrical systems that require flexibility and protection from vapors, liquids or solids. LFNC conduit should be used for liquid tight environment as stated by NEMA guidelines. All conduit and conduit fittings should be marked as "Liquid Tight" conduit and fittings marked "Rain Tight" or "Wet Locations" are not to be automatically considered liquid tight. NOTE: Select all conduit and conduit connectors based on local code and application of job. Slide threaded body into fitting hole in enclosure, 3. Insert gasket around threaded area and secure in place with nut provided. (Refer to manufacturer specifications for proper torque requirements. ) 4. Remove all resulting debris created by entry hole(s) otherwise electrical components and operation may be affected. TH E C EL HA M MB HU E RS RLA T, IL IN G LI NO ROU I S P, 6 0 IN 12 C. 6 ATTACHMENT TO ENCLOSURE N WARNING Do Not Run Power & Control Wiring in the Same Conduit 7 41 B6 PL AC ER LI ST ED AT I NG LA B EL H DO OR ER E OP ER AT OR CONTROL WIRING DETERMINE WIRING TYPE Refer to the wiring diagram located on the inside cover the electrical box to determine the type of control wiring. WIRING TYPES Standard C2 or B2 Wiring Standard operators are shipped from the factory with jumper set for C2 wiring, which requires constant pressure on button to close the door. If momentary contact on close direction is desired (B2 wiring) you must include an entrapment protection device. Constant pressure on close (C2 wiring) Red jumper wire was placed on terminal #2 in electrical enclosure. The operator will require constant pressure on close control in order to keep door moving in the close direction. Momentary contact on close (B2 wiring) Move red jumper wire from terminal #2 to terminal #3. [. . . ] · ALL power and control wiring MUST be run in separate conduit. ENT MANUAL DISCONNECT AVERTISSEMENT AVERTISSEMENT Disengagement Lever By turning the disengagement lever the gear unit can be disconnected from electric operation in order to permit manual operation of the door. For operating the lever from above floor level, attack a rope or a chain in the holes at the ends of the lever. The movement of the lever acts upon a safety micro switch, which will keep the control current disconnected until the lever has been turned absolutely perfectly into its position for normal electric operation of the door. To Engage Pull Handle CIA N ADVERTENCIA ADVERTENCIA To Disengage Pull Handle 14 WARNING CAUTION MAINTENANCE SCHEDULE WARNING WARNING Check at the intervals listed in the following chart. To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric power BEFORE performing ANY maintenance. ITEM Drive Chain PROCEDURE Check for excessive slack. Lubricate. * Check & tighten as required EVERY 3 MONTHS EVERY 6 MONTHS EVERY 12 MONTHS Sprockets Check AVERTISSEMENT set screw tightness Fasteners AVERTISSEMENT AVERTISSEMENT ATTENTION Bearings & Shafts Manual Disconnect Check & Operate Check for wear & lubricate Use SAE 30 Oil (Never use grease or silicone spray). [. . . ]