User manual CHAMBERLAIN HC260

[. . . ] Automatic Gate Opener Models , when installed and maintained according to all the Manufacturer's instructions in combination with a Gate, which has also been installed and maintained according to all the Manufacturer's instructions, meets the provisions of EU Directive 89/392/EEC and all amendments. I, the undersigned, hereby declare that the equipment specified above and any accessory listed in the manual conforms to the above Directives and Standards. This safety alert symbol means "Caution" - failure to comply with such an instruction involves risk of personal injury or damage to property. This gate drive mechanism is designed and tested to offer appropriately safe service provided it is installed and operated in strict accordance with the following safety rules. [. . . ] A gate can cause serious injuries as it closes. Disconnect electric power to the system before making repairs or removing covers. A disconnecting device must be provided in the permanently-wired installation to guarantee all-pole disconnection by means of a switch (at least 3mm contact gap) or by a separate fuse. Make sure that people who install, maintain or operate the gate drive and/or the control board are qualified and follow these instructions. Keep these instructions in a safe place so that you can refer to them quickly when you need to. Before that pull all plug ins from their sockets. a small bag contains jumpers for the control. These might be needed later on individual settings in the controls' programming. (refer to JUMPERS) Put the 4 large closure screws of the box through cover of the box. Fasten 2 of them (left or right) approx 2cm into the box. After that the cover may be opened to the side. Close box on a trial basis turning the screws all the way in. If the lid does not close completely, then the box is not fitted to the wall evenly and is therefore distorted. It is very important for the box to be waterproof once closed. A) start with still dead 230Volts supply cable on the left side of the box. Then connect ground wire to base plate with washer and nut (exactly as shown in picture detail). Otherwise motor might be damaged or will not operate properly. Pay special attention when using distribution boxes. we recommend the following accessories: LA400-JB40E Kit for cable extension of one installation unit. Consists of 12m of cable 6-pole with identical colours, distribution box IP65, cable screw joints and fastening material P1 button to program P2 button to program P3 button to program Description of LED's (light-emitting diode) Description Colour green Function monitors emergency switch or safety edge ON: blocks control board OFF: OK key switch ON: key switch is operating OFF: key switch is not operating Photocells 2 ON: OK (active) OFF: no photocell fitted Photocells 1 ON: OK (active) OFF: no photocell fitted learn mode indication ON: learn mode active OFF: learn mode inactive diagnosis mode Refer to FAQ's Brown cable green cable white cable yellow cable Motor2 brown cable green cable white cable yellow cable PHO2 key switch negative pole Photocells 1 Photocells 2 negative pole connector for emergency switch or safety edge with 8. 2KOhms connection for 801719 radio receiver connection for E-lock control board 24V power input from transformer. Only modify settings when control bord is disconnected. [. . . ] B: Motorcables have insufficient connection to contol board Yellow or white cable not wired or badly connected Limits for motor 1 have not been accepted Travel has not been programmed The process of programming has been interrupted Force to operate the gate is too high A: Gate is out of order B: Gate is rough-running C: Gate stopped through windload A: Repair gate B: Check if gate can be easily moved C: Do not operate gate by windstorm D: Reprogram travel to achieve sufficient level of fo Photocells 1 block installation A: Object blocks photocells B: Alignment of the lenses is incorrect C: Power supply to photocells is insufficient Photocells 2 block installation Emergency stop switch blocks installation Safety edge blocks installation A: Object obstructs safety edge B: Defective safety edge C: Power too low or broken wire in supply Power supply to control board is too low A: Defective supply 230V or malfunctioning contact B: Broken wire in supply cable (copper cable) C: The battery (accessory) to operate the gate whilst power failure is dead. The gate opener doesn't respond at all; no LED is on. Immediately after the gate has started moving, it stops and reverses. The gate opener does not open the gate fully. [. . . ]