User manual CHAMBERLAIN LA100

[. . . ] 845 Larch Avenue Elmhurst, Illinois 60126-1196 www. liftmaster. com RESIDENTIAL GATE OPERATOR Model LA100 For Residential Use Only Owner's Manual Please read this manual and the enclosed safety materials carefully!Periodic checks of the operator by a qualified technician are required to ensure safe operation. The model number label is located inside the control box of your operator. Serial # Installation Date TABLE OF CONTENTS 2-6 2 3 3 3 4 4 5-6 INTRODUCTION Safety Symbol and Signal Word Review Operator Specifications Carton Inventory Hardware Inventory Additional Items for Purchase Tools Needed Safety Installation Information 26-28 OPERATION AND MAINTENANCE 26 26 27 27 28 Important Safety Information Operation Manual Release Maintenance Troubleshooting 29-30 REPAIR PARTS 29 29 Control Box Gate Operator 7-9 7 8 9 PREPARATION AND OVERVIEW Single Gate Overview Check Your Gate Mounting Options 30 31 ACCESSORIES WARRANTY 10-17 10-12 13-17 INSTALLATION Mount the Control Box and Power Supply Attach Operator to Gate BACK TEMPLATE FOR POST BRACKET MOUNTING 18-20 WIRING 18-20 Connect Gate Operator to Control Box 21-25 PROGRAMMING 21 21-22 23 24 25 25 Before You Begin Programming Gate Travel (Limit Learn) Adding Additional Wireless Control Devices Safety Sensor Connections The Protector System® Entrapment Zone Safety Sensor Protection INTRODUCTION Safety Symbol and Signal Word Review This gate operator has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. WARNING Mechanical CAUTION WARNING WARNING Electrical WARNING CAUTION When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. [. . . ] By turning the Gate Force control clockwise will decrease the amount of force and turning the control counter clockwise will increase the force. TEST CLOSE FORCE With the gate in the open position and the Gate Force control set to MIN, place the cardboard container the gate operator was shipped in against the close side latch post, such that the gate will hit the box when it closes. Press the remote control to close the gate. The gate should reverse when the gate hits the box and return to the full open position. TEST OPEN FORCE With the gate in the closed position and the Gate Force control set to MIN, place the cardboard container against an entrapment area on the open side. Press the remote control to open the gate. The gate should reverse when the gate hits the box and return to the closed position. Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing gate. · Too much force on gate will interfere with proper operation of safety reversal system. · NEVER increase force beyond minimum amount required to close gate. · NEVER use force adjustments to compensate for a binding or sticking gate. · If one control (force or travel limits) is adjusted, the other control may also need adjustment. · After ANY adjustments are made, the safety reversal system MUST be tested. Gate MUST reverse on contact with a rigid object. s Out ide pe Pro rty Rigid Object id Ins eP er rop ty Programming 22 R17 The Gate Force Sensitivity Adjustment control can be adjusted to help eliminate nuisance reversals, however, the gate should be tested as stated above after any adjustment of the Gate Force control. Make small adjustments until adequate force is obtained to minimize nuisance reversals while maintaining reversals off the box as described above. Once the gate travel and learn limit have been programmed as described above, the gate is ready to be used. The gate can be controlled via wireless remote controls (see Accessories). To open the gate, the user must press and release the button on the remote control. The gate will begin opening and stop at the open position. To close the gate, the user must press and release the button on the remote control. The gate will begin closing and stop at the closed position. When the gate is traveling and another command is given from the remote control, the gate will stop. The next command given will make the gate travel in the opposite direction and stop at the corresponding open or closed position. FORCE Force Adjustment MIN MAX Adding Additional Wireless Control Devices The gate controller has the ability to learn 9 (total) wireless control devices such as additional remote controls or keyless entry (see accessories): To add additional Remote Control: 1. [. . . ] To order call: 1-800-528-2806 or visit our website www. liftmaster. com. Wireless Gate Doorbell Provides easy access to guest by ringing base station in the house. PRESS TO Simple installation allows home RING owner to grant visitor access with a push of the remote control button. PRESS RING TO 370LM 3-Button Mini-Remote Control with SECURITY® : With key ring and fastening strip. WGB315 365LM Universal Receiver Converts a 390 MHz Garage Door Opener to 315MHz and thus the same remote for the gate operator will work on the garage door. PRESS RING TO PRESS RING TO 30 PRESS Accessories WARRANTY POLICY LIFTMASTER® ONE YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the first retail purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of one year from the date of purchase. [. . . ]