User manual CHAMBERLAIN LA400

[. . . ] INSTALLATION/OPERATION MANUAL MODEL LA400 MEDIUM DUTY SWING GATE OPERATOR Radio Receiver Built on Board 315MHz 2 YEAR WARRANTY Serial # Primary Arm Serial # Secondary Arm Serial # Control Box Installation Date TABLE OF CONTENTS Introduction 2-5 Carton Inventory . . 3 Additional Items Needed for Installation . . 3 Operator Dimensions and Specifications . . 32 Safety Accessories for Secondary Entrapment Protection . [. . . ] NOTE: Used for Dual Gate installations only. TIMER TO CLOSE ENABLE Set the TIMER TO CLOSE to desired setting. The range is 0 to 180 seconds, 0 seconds is OFF. FORCE BI-PART DELAY TIMER TO CLOSE Minimun Force Maximum Force OFF MAX OFF MAX Your basic installation is now complete. 26 OPTIONAL CONTROL AND SAFETY DEVICES To Add or Reprogram a Remote Control 1. Press and release "LEARN XMITTER" button (LED will light up). Press and hold remote button, the LED will flash, alarm will beep twice and the LED will go out. Repeat steps 1 and 2 until all remote controls are programmed (50 remote controls maximum). NOTE: For highest level of security, we recommend the 315 MHz, Security® line of products. Refer to Accessories. R1 LEARN XMITTER Remote Control "LEARN XMITTER" Button P2 CLOSE EDGE J19 Ø14GP 89ØE 14GPØ89 Ø14LG 89ØE 14LGØ89 Ø14SK 89ØE 14SKØ89 J1 OPEN/EGE PHOTO L1 1 O N S8 LEARN XMITTER 2 OFF OFF SINGLE NO NO ON SAVE ON MAGLOCK DUAL MODE NC EDGE NC PHOTO 12345 S1 OPEN PHOTO CLOSE PHOTO 24V OVLD SWITCHED ACCESSORY POWER To Erase All Codes To deactivate any unwanted remote controls, first erase all codes: Press and hold the "LEARN XMITTER" button on logic board until the learn indicator light goes out (approximately 6 seconds). Reprogram each remote control or keyless entry you wish to use. NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 27 Dip Switch Settings SAVE SWITCH S1-1 This switch (S1-1) is used to save the settings for switches 2 through 5. NOTE: When setting switches, the save switch must be in the off position prior to setting or changing switches for the change to be saved. MAG DELAY ENABLE This switch (S1-2) enables the Maglock feature. On an open command there will be a . 5 second delay before the motor starts, to allow the Maglock to release. MODE DUAL/SINGLE This switch (S1-3) sets the mode as Dual or Single (Refer to page 24). SAFETY INPUTS Swing gates allow four safety inputs. A DIP switch is required for determining between N/O and N/C edges and N/O and N/C eyes. EDGE INPUT Set switch (S1-4) to the following settings: N/O Edge (Active Close) = N/O dry contact edge or monitored edge NOTE: Monitored Edges should be set in the N/O position, as the activation condition is shorting the terminals. EYE INPUT This switch (S1-5) differentiates between N/O and N/C dry contact photoelectric eye inputs. NOTE: Pulsing Chamberlain (CPS-L) photoelectric eyes will automatically learn in N/O mode (See Accessories). O N O N SAVE OFF SAVE ON 12345 12345 O N OFF OFF SINGLE NO NO ON ON DUAL NC NC SAVE MAGLOCK MODE EDGE PHOTO O N O N 12345 OFF MAG DELAY ON ON MAG DELAY OFF 12345 12345 S1 FACTORY DEFAULT SHOWN O N O N P2 J19 Ø14GPØ89ØE Ø14LGØ89ØE Ø14SKØ89ØE J1 CLOSE EDGE OPEN/EGE PHOTO L1 1 S8 LEARN XMITTER 2 OFF OFF SINGLE NO NO S1 ON SAVE ON MAGLOCK DUAL MODE NC EDGE NC PHOTO OPEN PHOTO CLOSE PHOTO GATE1 OFF OFF SINGLE NO NO ON ON DUAL NC NC 12345 12345 O N 12345 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS 24V GATE 2 OVLD SWITCHED ACCESSORY POWER O N OFF OFF SINGLE EDGE NO ON ON DUAL NC 12345 O N OFF OFF SINGLE EYE NO 28 ON ON DUAL NC 12345 Wire Stop Button (Optional) A jumper wire is factory installed between the stop and common input. Stop (N/C) - Stop only (does not reset alarm). [. . . ] Includes mounting hardware and electrical interface box. Commercial Protector System® (Direct Connect): Maximum range is 45' 24V. Includes mounting hardware. CPS-LN4 43 WARRANTY POLICY AND SERVICE LIFTMASTER® TWO YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the first purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. [. . . ]