User manual CHAMBERLAIN MSLDCBB3

[. . . ] 845 Larch Avenue Elmhurst, Illinois 60126-1196 www. liftmaster. com Radio Receiver Included Model MSLDCBB3 (MEGA SLIDE UL) 1/2 HP COMMERCIAL DUTY SLIDE GATE OPERATOR OWNER'S MANUAL THIS UNIT IS A CLASS 1, 2, 3, OR 4 SLIDE GATE OPERATOR FOR USE IN SLIDE GATE APPLICATIONS TABLE OF CONTENTS INTRODUCTION Carton Inventory. . 6 Safety Precautions for Open Roller Gates . . 8 REPAIR PARTS ACCESSORIES SAFETY ACCESSORIES FOR SECONDARY ENTRAPMENT PROTECTION REPAIR PARTS AND SERVICE WARRANTY INSTALLATION CHECK OFF LIST 20 21 22 22 23 24 INSTALLATION Concrete Pad . . 9 WIRING AND HOOKUP AC Power Hookup (120/230 Vac) . [. . . ] NOTE: Pulse to close will only work when gate is at full open position. SIREN will run for 5 minutes after 2nd sequential obstruction, then turns itself off, however operator will require a reset signal to J5 #4 to re-activate gate. In addition, cycling the power will also reset unit. Terminal 5 Safety - Safety edge(s) and safety loop input. This function will make the gate reverse and go back to the open position if it was closing. Input is for all NORMALLY OPEN contact safety devices. This input is disabled when gate is in the full closed position. Terminal 6 Close - ANTI-TAIL GATE close input. When using a vehicle detector, you must use the presence contacts (N. O. and C. ) This input will QUICK close gate after input is applied and then removed. It will stop the open cycle and reverse gate to close. (Example: Car crosses over close loop before gate reaches full open position ­ gate will reverse and close). NOTE: The close input also acts as a safety-stop in that if gate is closing and a tail-gater is sensed at the close input, the gate WILL STOP its closing motion and not continue to close until the close input is removed (car backs up) or gate is re-opened. Terminal 7 Back-Away (For Barrier Arm Gate ONLY) - This input is recommended for use with our Mega Arm barrier gates. For your Mega Slide UL, please use terminals 1, 2 or 3 for your free exit loop input. Terminal 8 Shadow Loop - This input operates as a hold open only when gate is a full open position. Terminals 9, 10, 11, 12 Common - These inputs used for common (0 Vdc) to above listed functions. NOTE: J5 inputs 1-8 are tied to LED indicators to assist in trouble shooting. 3-BUTTON CONTROL STATION: Not already in place. See diagram below. J5 Input #1 J5 Input #6 Open Close Stop JP2 Connector (NOTE: Siren will sound when stop button is depressed) J5 Commons #9-12 11 ACCESSORY CONNECTIONS These terminals will provide battery backed power to 24 Vdc devices and are located at the bottom of the electronic control board at J4 terminals 1 and 2. Terminal 1 is 24 Vdc (+) and number 2 is 0 Vdc (-). Peripheral CLASS 2 low voltage devices that require 24 Vdc power maybe connected here (500 ma. EXAMPLE: Vehicle detector, radio receiver. [. . . ] ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU. UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER'S LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may not apply to you. [. . . ]