User manual CHAMBERLAIN MT QUICK START

[. . . ] Begin with door in fully closed position. Press and release the LEARN button (LED will light). Every press and release of the STOP button will add 5 seconds to the Timer to Close. [. . . ] TTC will become enabled after the next open command. 1 2 3 4 5 SE CLO Electrical Box Logic Board Retaining Plate Limit Nuts D7 U4 D6 D5 D4 014A1030 TP1 C9 C21 C20 J4 C32 R25 U1 C31 L5 AUX ANT AUX ANT J2 ^^^^ C18 R27 D14 K2 LT C29 R24 P1 TTC LED 1 2 LEARN STOP CLOSE OPEN 3 4 5 6 7 D9 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN OP EN D7 U4 D6 D5 D4 014A1030 TP1 C9 C21 C20 J4 C32 R25 U1 C31 L5 AUX ANT AUX ANT J2 ^^^^ R27 C18 TTC D14 K2 LT C29 R24 P1 LEARN STOP CLOSE OPEN LED 1 2 3 4 5 6 7 D9 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN 1 2 3 USE COPPER WIRE ONLY 4 5 6 7 OPEN C21 U1 L5 AUX ANT AUX ANT J2 ^^^^ C18 R27 D14 K2 LT C29 R24 P1 TTC LED 1 2 LEARN STOP CLOSE OPEN 3 4 5 6 7 D9 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN White/Black White LiftMaster® CPS Safety Sensors TTC D14 LED LEARN C31 LMEP1 LMEP2 STOP COM CLOSE INTRLK Control Wiring Knockouts CONTROL WIRING 10 16-22 AWG Programming Remote Controls 7 6 5 3 SINGLE BUTTON REMOTE CONTROL Built in 315 MHz radio receiver permits as many as 20 Security® remote controls or dip switch remote controls in any combination. Press and release the LEARN button (LED will light). Press and hold the button on the remote control until the LED flashes rapidly, then release to complete programming (LED will go out). Repeat steps 1 and 2 for additional remote controls. Electrical Box Logic Board D7 U4 D6 D5 D4 014A1030 TP1 C9 C20 J4 C32 R25 STOP CLOSE OPEN 3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION NOTE: The feature will use 3 of the 20 memory channels in the operator. Press and hold the LEARN button (LED will light). Press the desired button on the logic board Open (OPEN, CLOSE or STOP). Press and hold the desired button of the remote Stop control until LED flashes rapidly, then release. Repeat steps 1 through 3 to program additional buttons. TO ERASE ALL REMOTE CONTROLS Press and hold the LEARN button (over 5 seconds) until the LED goes out. All programmed remote controls will be erased. 1 2 3 4 5 6 7 r ade He cket ra B QuickStart 2 2nd for the model MT/BMT door operator 6 1st IMPORTANT: This QuickStart is intended to highlight a typical installation. These instructions are not intended to be comprehensive. Because each application is unique, it is the responsibility of the purchaser, designer, installer and end user to ensure that the total door system is safe for its intended use. Please consult the manual and/or a qualified technician for further information. NOTE: Intended for Professional Installation Only. Visit www. LiftMaster. com to locate a professional installing dealer in your area. 5 3 7 5 A SAFETY DEVICE IS HIGHLY RECOMMENDED Pivot Shaft and Cotter Pins Open Side of Straight Arm Nylon Locking Nut Take-Up Bolt NEVER run Control wiring in same conduit as the Power wiring! OPEN CLOSE 8 STOP Pivot Bolt Arm Assembly 1 Approximately 4 Feet Door Bracket 6 inches Maximum Half the Height of the Door Edge Sensor 6 inches Maximum 1 Install the spacer brackets evenly down the track. The nylon pad on the spacer bracket must face up. (Two -3/4" bolts/nuts per spacer) 2 Install the idler wheel assembly in the second hole from the end of the track (Two - 1" bolts/nuts with lock washers). 3 Slide the trolley carriage into the tracks so that the take-up bolt will be facing toward the powerhead. [. . . ] Connect the power and earth ground to the operator terminal block. Follow ALL local electrical codes. 10 Run control wires through the control wiring conduit hole in the electrical box enclosure. 11 Adjust the limit switches to open and close door properly. Make sure the limit nuts are positioned between the limit switches before proceeding with adjustments. [. . . ]