User manual CHAMBERLAIN SL595

[. . . ] GL CO NT RO LL ER BO AR D HEAVY DUTY SLIDE GATE OPERATOR MODEL SL585 MODEL SL595 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date__________________ HEAVY DUTY, HARSH ENVIRONMENT SLIDE GATE OPERATOR MODELS SL585 AND SL595 ARE FOR VEHICULAR PASSAGE GATES ONLY AND ARE NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . 2 Operator Dimensions and Horsepower Chart . 4 IMPORTANT NOTES · BEFORE attempting to install, operate or maintain the operator, you MUST read and fully understand this manual and follow all safety instructions. · DO NOT attempt repair or service of your commercial door and gate operator unless you are an Authorized Service Technician. OPERATOR WARNINGS Safety Installation Information . [. . . ] · Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. AVERTISSEMENT WARNING AVERTISSEMENT To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED. CAUTION Set Output Duration For commercial applications, the receiver can be set for either constant or momentary closure on the output contacts. Use of constant closure is prohibited on residential garage door openers because it overrides the safety reversal devices. With the jumper in the "M" (Momentary) position, the contacts will close for 1/4 second regardless of the length of radio transmission. With the jumper in "C" (Constant) position, the contacts will stay closed as long as the radio continues transmitting (Figure 2). The receiver is factory set at M. FIGURE 1 Security Mode Terminals Jumper Security Mode Terminals Jumper HIGH SECURITY MODE ADVERTENCIA 18 AVERTISSEMENT ADVERTENCIA ATTENTION NORMAL SECURITY MODE R1 R2 R3 R4 PROGRAMMING THE REMOTE TO THE RECEIVER 1. Pry open the front panel of receiver case with a coin or a screwdriver. Re-connect power to operator (Figure 3). Press and release the "learn" button on the receiver. The learn indicator light will glow steadily for 30 seconds. Within 30 seconds, press and hold the button on the hand-held remote that you wish to operate your gate operator. The opener will now operate when the push button on either the receiver or the remote control is pressed. Repeat Steps 2 and 3 for each remote control that will be used to operate the gate operator. TO ERASE ALL REMOTE CONTROL CODES Press and hold the "learn" button on the receiver panel until the indicator light turns off (about 6 seconds). Then follow the steps above to reprogram each remote control. FIGURE 2 CONSTANT Jumper OPERATION Output Duration Terminals MOMENTARY Jumper OPERATION Output Duration Terminals FIGURE 3 OPENING RECEIVER OPEN RECEIVER Connect Antenna Indicator Light Learn Button M C P2 M Output Duration Terminals Security Mode Power Supply Jumper 24V 12V NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or remote control are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ACCESSORY WIRING REMOTELY MOUNTED STOP/RESET CONTROL WIRING · This control will function as a Stop/Reset command and is to be wired within line of sight of the gate. · Wire Stop/Reset control station to terminals 3 and 5 on the control box on the operator. Make sure that all Stop/Reset controls are wired in series. NORM HIGH 1 234567 Control Conduit Control Conduit 1 2 3 Terminals 6 & 5 (Com) - Soft Open These terminals are intended for use as a general open control. Accessories that may be wired to this input include: Telephone Entry Systems, Radio Receiver (Commercial Applications), Exit Loop Detector, Keypads, 7-Day Timer. [. . . ] Miller MGR20 2-wire electric edge in 5' (1. 5 m) lengths for 2" (5 cm) round post. Miller MGR20 2-wire electric edge in 5' (1. 5 m) lengths for 2" (5 cm) square post. VOLTAGE +24V ac/dc +24V ac/dc VOLTAGE +24V ac/dc +24V ac/dc +24V ac/dc +24V ac/dc 38 NOTES 39 WARRANTY POLICY AND SERVICE LIFTMASTER® TWO YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the final purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. [. . . ]